▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Tire safety standards and inspection – Motor Vehicle Theory motor mechanics lesson

Lesson 86 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Learn when NHTSA says a tire should be replaced, how to read its age from the sidewall, what tire pressure monitoring does, and how tires are checked in a state safety inspection.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains published guidance so that you can understand safety advice or an inspection result. It does not teach tire mounting or repair. Values are dated; check the official source before relying on them. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “NHTSA says to replace tires at 2/32 of an inch, yet many shops suggest changing them earlier. Why might that be?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using the pressure printed on the tire's sidewall. That number is the tire's maximum. The correct pressure is on the vehicle's Tire and Loading Information Label and in the owner's manual.
  • Thinking the TPMS light means the monthly check is not needed. The system warns only when a tire is significantly underinflated. NHTSA still says to check monthly.

Hands-on: With a qualified adult, look at (do not remove or adjust) the tires of a parked, switched-off car on level ground. Find the tread wear bars in the grooves, the size code and the last four digits of the DOT number on the sidewall, and the Tire and Loading Information Label on the driver's door edge. Write them down.

What you will learn

  • I can state the tread depth at which NHTSA says a tire should be replaced and describe the penny test.
  • I can read the week and year of manufacture from a Tire Identification Number.
  • I can explain what a tire pressure monitoring system does and does not do.
  • I can list the monthly tire checks a driver should make.

Key words

tread depth
The depth of the main grooves, measured from the top of the tread block to the bottom of the groove.
2/32 of an inch
The tread depth at which NHTSA says a tire should be replaced. It equals 1/16 of an inch, about 1.6 mm.
TPMS
Tire pressure monitoring system. It warns the driver when a tire is significantly underinflated.
Tire Identification Number
The code after the letters DOT on the sidewall. Its last four digits give the week and year the tire was made.

The big ideas

Tires are the only parts of a vehicle that touch the road. In the United States, the National Highway Traffic Safety Administration (NHTSA) publishes tire safety guidance for drivers, and states that run safety inspections check tires as part of the inspection. Rules differ from state to state, so always check your own state's requirements.

NHTSA says tires should be replaced when the tread is worn down to 2/32 of an inch. It also explains how to read a tire's age from the Tire Identification Number, where to find the correct pressure, and what a tire pressure monitoring system can and cannot tell you.

This lesson explains the standards so that you can understand tire advice and an inspection result. It is not a guide to mounting or repairing tires, which is work for a trained tire technician.

Read-through: the teaching steps

  1. Where tread depth is measured

    Tread depth is measured in the grooves. NHTSA says tires should be replaced when the tread is worn down to 2/32 of an inch. Tires have tread wear bars molded into the grooves; when the tread is level with the bars, it is worn out. See the drawing on the lesson page.

    Tread depthreplace at 2/32 inTread wear barTread blockGroove
    Tread depth is measured in the grooves. NHTSA says a tire should be replaced when the tread is worn down to 2/32 of an inch.
  2. The penny test

    NHTSA describes a quick check with a penny. Place the penny in the tread with Lincoln's head upside down and facing you. If you can see the top of Lincoln's head, the tread is worn and the tire should be replaced.

  3. How old is the tire?

    The Tire Identification Number follows the letters DOT on the sidewall. Its last four digits are the week and year of manufacture: 0308 means the third week of 2008. NHTSA notes that some manufacturers recommend replacing tires that are six to 10 years old, whatever the tread wear.

  4. The right pressure

    The correct pressure is the vehicle manufacturer's figure, shown on the Tire and Loading Information Label on the driver's door edge or doorjamb and in the owner's manual. It is not the number printed on the tire. NHTSA says to check all tires, and the spare, at least once a month when they are cold, which means the car has not been driven for at least three hours.

  5. Tire pressure monitoring

    A tire pressure monitoring system (TPMS) is required on passenger cars, light trucks and vans from model year 2008. It warns only when a tire is significantly underinflated, so it does not replace the monthly check. NHTSA says that if the light flashes for 60 to 90 seconds and then stays on, the system itself is malfunctioning.

  6. State inspections

    Some states require a periodic safety inspection, and tires, wheels and rims are among the items checked. In Virginia, for example, the State Police list tires, wheels and rims as one of the inspection steps, alongside brakes, lights, steering and suspension. Requirements, intervals and fees are set by each state, so check your own state's official source.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Wheels and tires lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.