Tyre law and inspection standards – Motor Vehicle Theory motor mechanics lesson
Lesson 86 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn the legal minimum tread depth for cars and motorcycles in the UK, how an MOT tester judges cuts, bulges and tyre pressure monitoring faults, and what the driver must check between tests.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains published standards so that you can understand a test result or safety advice. It does not teach tyre fitting or repair. Values are dated; check the official source before relying on them. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “The legal minimum is 1.6 mm, yet many tyre makers suggest changing tyres earlier. Why might that be?”
- Later: the homework, then the practice test.
Watch out for
- Thinking 1.6 mm must be present across the whole width of a car tyre. The car rule covers the central three-quarters of the breadth, all the way round. The outer quarters may be bald, though that points to a fault worth finding.
- Thinking a current MOT certificate proves the tyres are legal today. The test shows the condition on the day. The driver is responsible every time the vehicle is used.
Hands-on: With a qualified adult, look at (do not remove or adjust) the tyres of a parked, switched-off car on level ground. Find the tread wear indicators in the main grooves, the size code and the four-digit date code on the sidewall, and write them down. Note anything you would ask a tyre fitter about.
What you will learn
- I can state the minimum tread depth for cars and for motorcycles and where it is measured.
- I can describe how cuts, bulges and exposed cords are judged in the MOT.
- I can explain the MOT rule for tyre pressure monitoring systems.
- I can list the tyre checks a driver should make between tests.
Key words
- tread depth
- The depth of the main grooves, measured from the top of the tread block to the bottom of the groove.
- central three-quarters
- The middle 75% of the tread width. The car tread depth rule applies here, all the way round the tyre.
- TPMS
- Tyre pressure monitoring system. It warns the driver when a tyre has lost pressure.
- ply or cord
- The layers of fabric or steel inside the tyre that give it strength. They must never be visible.
The big ideas
Tyres are the only parts of a vehicle that touch the road, so the law sets standards for them. In the UK the standard that MOT testers apply is published by the DVSA in the MOT inspection manual, and the driver is responsible for the tyres every day, not only on the day of the test.
For cars, the primary grooves of the tread must be at least 1.6 mm deep within the central three-quarters of the breadth of the tread and around the entire outer circumference. Motorcycles need at least 1.0 mm. A tester also looks for cuts, lumps, bulges and exposed ply or cord, and checks the tyre pressure monitoring warning lamp on newer cars.
This lesson explains the standards so that you can understand a test result. It is not a guide to fitting or repairing tyres, which is work for a trained fitter.
Read-through: the teaching steps
Where tread depth is measured
Tread depth is measured in the primary grooves. For cars first used on or after 3 January 1933, the grooves must be at least 1.6 mm deep within the central three-quarters of the breadth of the tread, around the entire outer circumference. The outer quarters may be worn smooth. See the drawing on the lesson page.
Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round. Other vehicles
The 1.6 mm figure is for cars, light vans and light trailers. Motorcycles, large vehicles and passenger-carrying vehicles need at least 1 mm. Mopeds need visible tread. In the motorcycle MOT manual, the 1.0 mm must be present throughout a single band of at least three-quarters of the tread breadth, all the way round; motorcycles up to 50 cc need a visible tread pattern instead.
Defect categories for tread
Since May 2018 MOT defects are graded. A dangerous defect is a direct and immediate risk to road safety; a major defect may affect safety; both fail the test. A minor defect passes, and an advisory is a note to monitor. Tread depth below the requirement is a dangerous defect.
Cuts, bulges and cords
A tester fails a tyre if any ply or cord is visible. A cut longer than 25 mm or 10% of the section width, whichever is greater, fails if it is deep enough to reach the ply or cords. A lump, bulge or tear caused by separation or partial failure of the structure is a dangerous defect. Testers are told to tell normal undulations in a radial tyre apart from a real bulge.
Tyre pressure monitoring
The MOT TPMS check applies to passenger cars (category M1) first used on or after 1 January 2012. A system that is malfunctioning or obviously not working is a major defect. The lamp normally lights briefly when the ignition is switched on. A lamp that stays on because pressure is low is not, by itself, a system fault.
The driver's duty
The Highway Code advises checking tyre pressures weekly, before a journey, when the tyres are cold, because warm tyres can give a misleading reading. GOV.UK warns that a vehicle can be unsafe even with a current MOT certificate, and that driving a vehicle in a dangerous condition can bring a fine of up to £2,500, a driving ban and 3 penalty points.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Wheels and tyres lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- DVSA MOT inspection manual: cars and passenger vehicles – 5. Axles, wheels, tyres and suspension
- DVSA MOT inspection manual: motorcycles – 5. Wheels, tyres and suspension
- GOV.UK – Check your vehicle is safe to drive
- The Highway Code – Annex 6. Vehicle maintenance, safety and security
- DVSA – Overview of MOT changes from May 2018
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.