▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

The altimeter: how it works, the subscale and its errors – Private Pilot Theory aviation lesson

Lesson 162 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Discover how an aneroid altimeter turns pressure into altitude, what the altimeter setting does, and why "going from a high to a low, look out below".

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the error rule "high to low, look out below" is so important for terrain clearance?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the altimeter setting corrects for temperature. It corrects only for pressure; in cold air true altitude is lower than indicated.
  • Getting the direction of the error wrong. High to low, look out below: a setting higher than the actual pressure makes the altimeter over-read.
  • Forgetting the temperature error. Colder than standard → true altitude lower than indicated.

Hands-on: Squeeze a sealed, half-empty plastic bottle with its cap on and watch it resist; take it up a hill or tall building and notice it puff out slightly as the outside pressure falls. That expanding "capsule" is how an aneroid altimeter works.

What you will learn

  • I can explain how sealed aneroid wafers measure height.
  • I can explain the altimeter setting and the 29.92 inHg standard setting.
  • I can work out an altimeter error using 1,000 ft per inch of mercury.
  • I can explain the effect of colder-than-standard air.
  • I can apply "high to low, look out below".

Key words

aneroid wafers
Sealed, flexible capsules that expand as outside pressure falls.
altimeter setting
Station pressure reduced to sea level; set it and the altimeter reads altitude above mean sea level.
Kollsman window
The window showing the altimeter setting, in inches of mercury and/or millibars.
29.92 inHg
The standard setting, used for flight levels in the US at and above 18,000 ft.
true altitude
The actual height above mean sea level.

The big ideas

An altimeter is a barometer marked in feet. The PHAK (chapter 8) describes sealed aneroid wafers that are squeezed by higher outside pressure and expand as pressure falls; the movement drives the pointers. Because pressure changes from day to day, the pilot sets the current altimeter setting in the Kollsman window.

The altimeter setting is station pressure reduced to sea level, and the handbook says it is accurate only near the reporting station, so it is updated en route. Set correctly, the altimeter reads altitude above mean sea level. The standard setting 29.92 inHg gives pressure altitude, and in the US it is used for flight levels from 18,000 ft. A rule of thumb from the handbook: 1 inch of pressure is about 1,000 ft. Before flight, if the altimeter differs from the surveyed field elevation by more than 75 ft, the handbook says it should go to a repair station.

Two errors matter. If pressure falls along the route and the setting is not updated, the altimeter over-reads: "going from a high to a low, look out below". And in colder-than-standard air true altitude is lower than indicated – "from hot to cold, look out below". This is theory for understanding only.

Read-through: the teaching steps

  1. Aneroid wafers

    Sealed capsules sit inside the case, which is connected to the static port. Higher pressure squashes them (lower reading); lower pressure lets them expand (higher reading).

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 29.92 inHgAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  2. The altimeter setting

    • Altimeter setting (local) → altitude above mean sea level; accurate only near the reporting station, so it is updated en route.
    • 29.92 inHg → pressure altitude; in the US used for flight levels at and above 18,000 ft.
  3. Converting pressure to feet

    Rule of thumb: 1 inch of mercury ≈ 1,000 ft. A 0.20 inch error ≈ 200 ft.

  4. High to low, look out below

    If you fly from high pressure towards low pressure without resetting, the altimeter reads higher than your true altitude. Example: set to 30.12, actual 29.92 → reads about 0.20 × 1,000 = 200 ft too high.

  5. Temperature error

    In air colder than standard, true altitude is lower than indicated. The pressure setting does not correct for temperature – "from hot to cold, look out below".

  6. Pre-flight check

    Set the current altimeter setting on the ground: the altimeter should read field elevation. The handbook says if it is more than 75 ft out, the instrument should be referred to a certificated repair station.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: FAA Pilot’s Handbook of Aeronautical Knowledge, chapter 8: flight instruments (free PDF) (opens in a new tab).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.