Pitot-static system and its errors – Private Pilot Theory aviation lesson
Lesson 161 of 228 in the Private Pilot Theory course (ages 16+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Learn how the pitot tube and static ports feed the airspeed indicator, altimeter and VSI, and work out what each instrument shows when a tube becomes blocked.
- Time
- 45 minutes + 10 min homework
- Course
- Private Pilot Theory (ages 16+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.
How to use this lesson
This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why does a blocked static port cause so many different instruments to give wrong readings at once?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the altimeter uses the pitot tube. The altimeter and VSI use static pressure only.
- Mixing up the two pitot blockages. Drain open → ASI to zero; drain blocked too → ASI acts like an altimeter.
- Expecting the alternate static source to read low. Cabin pressure is lower than outside, so the altimeter and ASI read slightly high.
Hands-on: Blow gently into the end of a drinking straw held against your palm (a "pitot") and then hold it sideways to the airflow from a fan (a "static port"). Feel the difference in pressure. Then press your finger over the end and imagine what an instrument connected to it would show.
What you will learn
- I can say which instruments use pitot and which use static pressure.
- I can explain what the airspeed indicator actually measures.
- I can predict the effect of a blocked pitot tube.
- I can predict the effect of a blocked static port.
- I can explain the effect of using the alternate static source.
Key words
- pitot tube
- A forward-facing tube that senses total (dynamic + static) pressure.
- static port
- A flush opening on the side of the aircraft that senses still-air pressure.
- dynamic pressure
- The extra pressure due to the aircraft's motion through the air.
- alternate static source
- A backup static source, usually inside the cabin.
- blockage
- Ice, insects or dirt closing a pitot or static opening.
The big ideas
The PHAK (chapter 8) explains that the pitot-static system feeds three instruments: the airspeed indicator (ASI), the altimeter and the vertical speed indicator (VSI). The pitot tube faces forward and measures total pressure – dynamic plus static. The ASI subtracts the static pressure from it, leaving dynamic pressure, which it shows as airspeed. The altimeter and VSI use static pressure only.
Because each instrument depends on particular openings, a blockage gives predictable wrong readings. A blocked pitot tube with its drain hole open makes the ASI fall to zero. If the pitot tube and drain are both blocked, the ASI no longer responds to speed but behaves like an altimeter. A blocked static port freezes the altimeter, holds the VSI at zero and makes the ASI read wrongly.
If the static port is blocked, many aircraft have an alternate static source inside the cabin. Cabin pressure is a little lower than outside, so the handbook says the altimeter and ASI read slightly high and the VSI shows a brief climb. This is theory for understanding only.
Read-through: the teaching steps
Which instrument uses what?
- ASI: pitot (total) and static
- Altimeter: static only
- VSI: static only
The “six-pack”: the six basic flight instruments in their usual layout. How the ASI works
Total pressure (from the pitot) minus static pressure = dynamic pressure, which depends on speed. The ASI shows that difference as airspeed.
Blocked pitot tube
- Pitot blocked, drain open: the pressure leaks away and the ASI drops to zero.
- Pitot and drain both blocked: trapped pressure stays fixed. The ASI no longer responds to speed, but it reacts to height changes as the static pressure changes – it acts like an altimeter.
Blocked static port
- Altimeter freezes at the altitude where the blockage happened.
- VSI reads zero continuously.
- ASI reads low above the blockage altitude and high below it.
Alternate static source
Inside the cabin the pressure is slightly lower than outside. With the alternate source selected the handbook says the altimeter reads slightly high, the ASI reads high, and the VSI shows a momentary climb.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.