▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

The altimeter: how it works, the subscale and its errors – Private Pilot Theory aviation lesson

Lesson 162 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Discover how an aneroid altimeter turns pressure into height, what the hPa subscale settings QNH, QFE and 1013 do, and why "high to low, look out below".

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the error rule "high to low, look out below" is so important for terrain clearance?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking QFE gives altitude above sea level. QFE gives height above the aerodrome; QNH gives altitude above mean sea level.
  • Getting the direction of the error wrong. High to low, look out below: a setting higher than the actual pressure makes the altimeter over-read.
  • Forgetting the temperature error. Colder than standard → true altitude lower than indicated.

Hands-on: Squeeze a sealed, half-empty plastic bottle with its cap on and watch it resist; take it up a hill or tall building and notice it puff out slightly as the outside pressure falls. That expanding "capsule" is how an aneroid altimeter works.

What you will learn

  • I can explain how sealed aneroid wafers measure height.
  • I can explain the QNH, QFE and 1013 hPa settings.
  • I can work out an altimeter error using 27 ft per hPa.
  • I can explain the effect of colder-than-standard air.
  • I can apply "high to low, look out below".

Key words

aneroid wafers
Sealed, flexible capsules that expand as outside pressure falls.
QNH
The setting that makes the altimeter read altitude above mean sea level.
QFE
The setting that makes the altimeter read height above the aerodrome (zero on the ground).
1013 hPa
The standard setting used for flight levels above the transition altitude.
true altitude
The actual height above mean sea level.

The big ideas

An altimeter is a barometer marked in feet. The PHAK (chapter 8) describes sealed aneroid wafers that are squeezed by higher outside pressure and expand as pressure falls; the movement drives the pointers. Because pressure changes from day to day, the pilot sets the current pressure on a subscale.

The UK Skyway Code explains the settings: QNH makes the altimeter read altitude above mean sea level; QFE makes it read height above the aerodrome, so it shows zero on the ground; and the standard setting 1013 hPa is used for flight levels above the transition altitude. It notes that 1 hPa is about 27 ft, and that the Regional Pressure Setting – the lowest forecast pressure in a region – normally makes the altimeter under-read your altitude, a safe-side error.

Two errors matter. If the pressure falls along the route and the setting is not updated, the altimeter over-reads: "going from a high to a low, look out below". And in colder-than-standard air true altitude is lower than indicated – the pressure setting does not correct for temperature. This is theory for understanding only.

Read-through: the teaching steps

  1. Aneroid wafers

    Sealed capsules sit inside the case, which is connected to the static port. Higher pressure squashes them (lower reading); lower pressure lets them expand (higher reading).

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 1013.25 hPaAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  2. The subscale settings

    • QNH → altitude above mean sea level
    • QFE → height above the aerodrome (zero on the ground)
    • 1013 hPa → flight levels, above the transition altitude

    The Skyway Code gives the transition altitude as 3,000 ft outside controlled airspace (higher within some controlled airspace).

  3. Converting pressure to feet

    Near sea level 1 hPa ≈ 27 ft (Skyway Code). A 10 hPa error ≈ 270 ft.

  4. High to low, look out below

    If you fly from high pressure towards low pressure without resetting the subscale, the altimeter reads higher than your true altitude. Example: subscale on 1023, actual QNH 1013 → reads about 10 × 27 = 270 ft too high.

  5. Temperature error

    In air colder than standard, true altitude is lower than indicated. The pressure setting does not correct for temperature – "from hot to cold, look out below".

  6. Regional Pressure Setting

    The RPS is the lowest forecast pressure in a region. Set on the subscale, it normally makes the altimeter under-read your altitude – the error is on the safe side for terrain clearance.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: CAA Skyway Code (CAP 1535) (opens in a new tab).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.