▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Pressure altitude from QNH or altimeter setting – worked example – Private Pilot Theory aviation lesson

Lesson 183 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

Convert an airport's elevation and altimeter setting into pressure altitude using 1,000 ft per inch of mercury – the first step towards density altitude.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why does a performance chart ask for pressure altitude rather than the aerodrome's elevation?”
  4. Later: the homework, then the practice test.

Watch out for

  • Getting the sign wrong. Low setting → higher pressure altitude (add).
  • Forgetting to multiply by 1,000. 0.20 inch is 200 ft, not 0.2 ft.
  • Using pressure altitude as if it were density altitude. Pressure altitude still needs the temperature correction.

Hands-on: Find today's altimeter setting for your nearest airport on a weather website and the airport's elevation. Work out its pressure altitude with 1,000 ft per inch.

What you will learn

  • I can define pressure altitude.
  • I can convert an altimeter-setting difference from 29.92 inHg into feet using 1,000 ft per inch.
  • I can decide whether to add or subtract the correction.
  • I can find pressure altitude by setting the standard value.
  • I can combine the result with a density altitude calculation.

Key words

pressure altitude
The altitude shown when 29.92 inHg is set in the Kollsman window.
altimeter setting
The local setting that gives altitude above mean sea level.
standard pressure
29.92 inHg.
elevation
Height of the aerodrome above mean sea level.
conversion factor
About 1,000 ft per inch of mercury (PHAK).

The big ideas

Pressure altitude is the altitude in the standard atmosphere that matches the pressure where you are. The PHAK (chapter 11) says that setting 29.92 inHg on the altimeter shows it directly; otherwise the correction can be worked out from the field elevation. The handbook's chart, for example, adds 205 ft for an altimeter setting of 29.7.

The PHAK rule of thumb is about 1,000 ft per inch of mercury. If the altimeter setting is lower than 29.92, pressure altitude is higher than the elevation; if it is higher than 29.92, pressure altitude is lower:

pressure altitude = elevation + (29.92 − altimeter setting) × 1,000 ft

Pressure altitude is then the starting point for a density altitude estimate. This is theory for understanding only.

Read-through: the teaching steps

  1. Two ways to find it

    • Set 29.92 inHg and read the altimeter.
    • Or calculate from elevation and the altimeter setting.
  2. The conversion

    About 1,000 ft per inch (PHAK). 0.20 inch ≈ 200 ft.

  3. Add or subtract?

    Setting below 29.92 → pressure altitude above elevation (add). Setting above 29.92 → pressure altitude below elevation (subtract).

  4. The formula

    Pressure altitude = elevation + (29.92 − setting) × 1,000

  5. Next step: density altitude

    Use the pressure altitude to find the ISA temperature, then the ISA deviation, then density altitude (see the density altitude lesson).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Flight Performance and Planning lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.