▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Pressure altitude from QNH or altimeter setting – worked example – Private Pilot Theory aviation lesson

Lesson 183 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Convert an aerodrome's elevation and QNH into pressure altitude using 27 ft per hPa – the first step towards density altitude.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why does a performance chart ask for pressure altitude rather than the aerodrome's elevation?”
  4. Later: the homework, then the practice test.

Watch out for

  • Getting the sign wrong. Low QNH → higher pressure altitude (add).
  • Using 30 ft per hPa when the question says 27. Use the figure stated in the stem.
  • Using pressure altitude as if it were density altitude. Pressure altitude still needs the temperature correction.

Hands-on: Find today's QNH for your nearest airport on a weather website and the airport's elevation. Work out its pressure altitude with 27 ft per hPa.

What you will learn

  • I can define pressure altitude.
  • I can convert a QNH difference from 1013 hPa into feet using 27 ft per hPa.
  • I can decide whether to add or subtract the correction.
  • I can find pressure altitude by setting the standard value.
  • I can combine the result with a density altitude calculation.

Key words

pressure altitude
The altitude shown when 1013 hPa is set on the subscale.
QNH
The pressure setting that gives altitude above mean sea level.
standard pressure
1013 hPa (1013.25 hPa).
elevation
Height of the aerodrome above mean sea level.
conversion factor
About 27 ft per hPa near sea level (Skyway Code).

The big ideas

Pressure altitude is the altitude in the standard atmosphere that matches the pressure where you are. The PHAK (chapter 11) says that setting the standard pressure on the altimeter shows it directly; otherwise the correction can be worked out from the field elevation.

The UK Skyway Code gives 1 hPa as about 27 ft. If the QNH is lower than 1013 hPa, the air at the aerodrome has a lower pressure than standard for its height, so the pressure altitude is higher than the elevation. If QNH is higher than 1013, pressure altitude is lower than the elevation:

pressure altitude = elevation + (1013 − QNH) × 27 ft

Textbooks use 27 or 30 ft per hPa, so every question here states the figure. Pressure altitude is then the starting point for a density altitude estimate. This is theory for understanding only.

Read-through: the teaching steps

  1. Two ways to find it

    • Set 1013 hPa and read the altimeter.
    • Or calculate from elevation and QNH.
  2. The conversion

    About 27 ft per hPa (Skyway Code). 10 hPa ≈ 270 ft.

  3. Add or subtract?

    QNH below 1013 → pressure altitude above elevation (add). QNH above 1013 → pressure altitude below elevation (subtract).

  4. The formula

    Pressure altitude = elevation + (1013 − QNH) × 27

  5. Next step: density altitude

    Use the pressure altitude to find the ISA temperature, then the ISA deviation, then density altitude (see the density altitude lesson).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Flight Performance and Planning lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.