Density altitude: how to calculate it – worked example – Private Pilot Theory aviation lesson
Lesson 182 of 228 in the Private Pilot Theory course (ages 16+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Work out density altitude from pressure altitude and temperature with a rule of thumb, and see why hot, high and humid days hurt performance.
- Time
- 45 minutes + 10 min homework
- Course
- Private Pilot Theory (ages 16+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.
How to use this lesson
This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why might an airfield high in the mountains be fine for a light aircraft on a cold morning but marginal on a hot afternoon?”
- Later: the homework, then the practice test.
Watch out for
- Using the actual temperature instead of the deviation. Subtract the ISA temperature first: 2,000 + 25 × 120 = 5,000 ft is wrong.
- Forgetting that ISA temperature falls with height. At 4,000 ft ISA is 7 °C, not 15 °C.
- Thinking a negative density altitude is impossible. It just means the air is denser than ISA sea level.
Hands-on: Look up today's temperature and the height of your town above sea level. Work out the ISA temperature for that height and today's ISA deviation. Would density altitude be above or below your real height?
What you will learn
- I can define density altitude.
- I can find the ISA temperature at a pressure altitude.
- I can calculate the ISA deviation.
- I can estimate density altitude using a stated rule of thumb.
- I can explain the effect of density altitude on performance.
Key words
- density altitude
- Pressure altitude corrected for non-standard temperature.
- ISA
- International Standard Atmosphere: 15 °C at sea level, falling about 2 °C per 1,000 ft.
- ISA deviation
- Actual temperature minus ISA temperature at that altitude.
- pressure altitude
- Altitude shown with the standard setting, 29.92 inHg.
- rule of thumb
- A simple approximation – here, 120 ft of density altitude per °C of ISA deviation.
The big ideas
The PHAK (chapter 11) defines density altitude as pressure altitude corrected for nonstandard temperature. It is the altitude in the standard atmosphere where the air would have the same density as the air you are in. High density altitude comes from high elevation, low pressure, high temperature and high humidity – and the higher it is, the worse the airplane performs. Density altitude is one of the FAA private pilot knowledge areas.
To estimate it, first find the standard (ISA) temperature at the pressure altitude: 15 °C at sea level, falling about 2 °C per 1,000 ft (the PHAK lapse rate). The ISA deviation is the actual temperature minus that. A common rule of thumb then adds about 120 ft of density altitude for each °C above ISA (and subtracts for each °C below). Textbooks use 118.8 or 120 ft per °C, so every question here states the figure it uses.
Density altitude = pressure altitude + 120 × (OAT − ISA temperature). Real aircraft manuals use charts for this; this lesson is for understanding only.
Read-through: the teaching steps
What density altitude means
The air's density decides how well the wing lifts, the propeller bites and the piston engine breathes. Density altitude expresses that density as an altitude in the standard atmosphere.
The International Standard Atmosphere (ISA) – a reference, not the real weather on any day. ISA temperature
ISA temperature ≈ 15 − 2 × (pressure altitude ÷ 1,000) °C.
At 3,000 ft: 15 − 6 = 9 °C.
ISA deviation
Deviation = actual temperature − ISA temperature.
At 3,000 ft with 24 °C: 24 − 9 = +15 (ISA +15).
The rule of thumb
Density altitude ≈ pressure altitude + 120 × deviation.
3,000 + 120 × 15 = 3,000 + 1,800 = 4,800 ft.
Cold days
If it is colder than ISA the deviation is negative and density altitude is lower than pressure altitude – it can even be below sea level, which simply means the air is denser than standard sea-level air.
Why it matters
High density altitude → longer take-off roll, lower climb rate, higher true airspeed at lift-off for the same indicated airspeed. Humidity makes it worse (moist air is less dense), though the rule of thumb does not include it.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Flight Performance and Planning lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.