▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Charging: AC, DC and connector types – Vehicles and Technology motor mechanics lesson

Lesson 5 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out why some chargers are slow and some are rapid, what the difference between AC and DC charging really is, and which connectors UK chargepoints use – with the maths to work out charging times.

Time
45 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson needs only multiplication and division. If you visit a public charger together, look at the connectors and information labels without touching the equipment. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If every car were electric, where would the best places be to put rapid chargers, and why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a bigger AC chargepoint always charges faster. On AC, the car's onboard charger can be the limit. A 22 kW chargepoint charges a car with a 7 kW onboard charger at only about 7 kW.
  • Thinking DC charging stays at full speed until 100%. The battery management system reduces the current as the battery fills, so the last part is much slower.
  • Mixing up kW and kWh. kW is the charging speed (power); kWh is the amount of energy added.

Hands-on: Make a charging-time chart on paper. Down the side write energy needed: 10, 20, 30, 40 and 50 kWh. Across the top write chargepoint powers: 3.6, 7, 22 and 50 kW. Fill in each box with the time in hours (energy ÷ power), rounded to one decimal place. Then circle the boxes where a car with a 7 kW onboard charger would actually be slower than your answer, and explain why. If you see a public chargepoint with an adult, look at the connector shapes from a safe distance – do not touch the equipment.

What you will learn

  • I can explain the difference between AC charging and DC charging.
  • I can explain why the onboard charger limits AC charging speed.
  • I can describe the UK chargepoint power classes and the Type 2 connector.
  • I can use P = V × I and time = energy ÷ power to work out charging.
  • I can explain why charging slows down as the battery fills.

Key words

AC charging
Charging from an alternating-current supply. The car's onboard charger converts it to DC.
DC charging
Charging where the chargepoint converts the power to DC itself and feeds the battery directly – used for rapid charging.
Type 2 connector
The standard connector for AC chargepoints in the UK, set out in the British Standard BS EN 62196.
CCS
Combined Charging System: a car port that adds two large DC pins to the AC connector so one port handles both AC and DC.
state of charge
How full the battery is, as a percentage.
kilowatt (kW)
A unit of power – how fast energy flows into the battery.

The big ideas

A battery can only store direct current (DC), but the electricity grid supplies alternating current (AC). Somewhere between the grid and the battery, AC must be turned into DC. Where that happens is the big difference between charging types.

With AC charging – at home, at work or at many street chargepoints – the chargepoint mainly supplies AC safely, and the car's own onboard charger converts it. So the speed is limited by whichever is smaller: the chargepoint's output or the onboard charger's rating. With DC charging, a large converter inside the chargepoint does the conversion and sends DC straight to the battery, which allows much higher power.

The UK government's minimum technical specification for commercial chargepoints groups AC chargepoints by power (for example standard AC above 3.5 kW up to 7 kW on a 230 V single-phase supply, and fast AC above 7 kW up to 23 kW) and requires AC chargepoints to use the Type 2 connector or socket where applicable. DC equipment uses a separate charging mode.

This is explanation for understanding, not a guide to using or installing charging equipment. Chargepoints are installed by qualified electricians, and the car's high-voltage system is for trained technicians only.

Read-through: the teaching steps

  1. AC versus DC: where the conversion happens

    Picture the charging chain: grid → chargepoint → cable → car's charge port → (onboard charger) → battery.

    • AC charging: AC travels all the way into the car; the onboard charger converts it.
    • DC charging: the chargepoint converts it; DC goes straight to the battery and the onboard charger is bypassed.

    Onboard chargers have to fit in the car, so they are much smaller than the converters in DC charging units.

    Traction battery pack (under the floor)Electric traction motorPower electronicsCharge port
    The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only.
  2. UK power classes

    The UK government specification for commercial chargepoints sets these classes (power at each outlet):

    • Standard AC: above 3.5 kW to 7 kW, 230 V single-phase
    • Fast AC: above 7 kW to 23 kW, 230 V single-phase or 400 V three-phase
    • Semi-rapid AC: above 23 kW to 43 kW, 400 V three-phase
    • Rapid DC: above 50 kW to 62.5 kW

    Slow AC below 3.5 kW is not allowed under that specification. Higher-power DC equipment also exists at some sites.

  3. Connectors

    UK AC chargepoints use the Type 2 connector (from the British Standard BS EN 62196), either as a socket you plug your own cable into or as a cable fixed to the chargepoint (tethered).

    For DC rapid charging, most cars use a CCS (Combined Charging System) port: the Type 2 shape with two large DC pins added underneath, so one port handles both AC and DC. Some older cars use a separate DC connector called CHAdeMO.

  4. Power, voltage and current

    Charging power follows P = V × I (power = voltage × current).

    • A 230 V supply at 32 A gives 230 × 32 = 7,360 W, about 7.4 kW.
    • A battery at 400 V taking 125 A of DC receives 400 × 125 = 50,000 W = 50 kW.

    High charging power needs either high voltage, high current, or both. High current needs thick cables, which is why rapid chargers have heavy, often liquid-cooled cables.

  5. Charging time

    Charging time (hours) = energy needed (kWh) ÷ charging power (kW).

    To add 40 kWh at 7 kW takes 40 ÷ 7 ≈ 5.7 hours. At 50 kW it would take about 0.8 hours (48 minutes) – if the car could take 50 kW the whole time. Real times are a little longer because some energy is lost as heat in the charger and battery.

  6. Why charging slows down

    The battery management system protects the cells. As the battery fills, the cell voltages rise and the system reduces the current to avoid overcharging and overheating. So DC charging is fastest when the battery is fairly empty and slows down a lot near full.

    This is why rapid charging is usually quoted as time to reach about 80%, and why the AFDC says actual charging power varies by vehicle and battery state of charge. A cold battery also charges more slowly until it warms up.

  7. Safety

    Chargepoints are fixed electrical installations put in by qualified electricians. The cable and connector are designed so no live pins can be touched, and power flows only after the car and chargepoint have "talked" and agreed it is safe. Never use a damaged cable, never use extension leads unless the maker allows it, and leave anything inside the car's high-voltage system to trained technicians.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Electric and hybrid vehicles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.