▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Charging: AC, DC and connector types – Vehicles and Technology motor mechanics lesson

Lesson 5 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out why some chargers are slow and some are fast, what Level 1, Level 2 and DC fast charging really mean, and which connectors US chargers use – with the math to work out charging times.

Time
45 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson needs only multiplication and division. If you visit a public charger together, look at the connectors and information labels without touching the equipment. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If every car were electric, where would the best places be to put rapid chargers, and why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a bigger AC chargepoint always charges faster. On AC, the car's onboard charger can be the limit. A 22 kW chargepoint charges a car with a 7 kW onboard charger at only about 7 kW.
  • Thinking DC charging stays at full speed until 100%. The battery management system reduces the current as the battery fills, so the last part is much slower.
  • Mixing up kW and kWh. kW is the charging speed (power); kWh is the amount of energy added.

Hands-on: Make a charging-time chart on paper. Down the side write energy needed: 10, 20, 30, 40 and 50 kWh. Across the top write charger powers: 1.9, 7.2, 19.2 and 50 kW. Fill in each box with the time in hours (energy ÷ power), rounded to one decimal place. Then circle the boxes where a car with a 7.2 kW onboard charger would actually be slower than your answer, and explain why. If you see a public charger with an adult, look at the connector shapes from a safe distance – do not touch the equipment.

What you will learn

  • I can explain the difference between AC charging and DC charging.
  • I can explain why the onboard charger limits AC charging speed.
  • I can describe Level 1, Level 2 and DC fast charging and their connectors.
  • I can use P = V × I and time = energy ÷ power to work out charging.
  • I can explain why charging slows down as the battery fills.

Key words

AC charging
Charging from an alternating-current supply. The car's onboard charger converts it to DC.
DC fast charging
Charging where the station converts the power to DC itself and feeds the battery directly.
Level 1 and Level 2
AC charging at 120 V (Level 1) or 208–240 V (Level 2).
J1772
The standard connector for Level 1 and Level 2 charging in the US.
CCS
Combined Charging System: the J1772 port with two extra DC pins added below, so one port handles AC and DC.
state of charge
How full the battery is, as a percentage.

The big ideas

A battery can only store direct current (DC), but the electricity grid supplies alternating current (AC). Somewhere between the grid and the battery, AC must be turned into DC. Where that happens is the big difference between charging types.

With AC charging – Level 1 and Level 2 – the charging equipment mainly supplies AC safely, and the car's own onboard charger converts it. So the speed is limited by whichever is smaller: the equipment's output or the onboard charger's rating. With DC fast charging, a large converter in the station does the conversion and sends DC straight to the battery, which allows much higher power.

The US Department of Energy's Alternative Fuels Data Center (AFDC) describes the three levels: Level 1 uses a 120 V outlet and gives about 5 miles of range per hour; Level 2 uses 240 V (home) or 208 V (commercial) and gives about 25 miles per hour; DC fast charging, at up to 500 kW, gives about 100 to 200+ miles of range in 30 minutes. Actual power depends on the vehicle and how full the battery is.

This is explanation for understanding, not a guide to using or installing charging equipment. Charging equipment is installed by licensed electricians, and the car's high-voltage system is for trained technicians only.

Read-through: the teaching steps

  1. AC versus DC: where the conversion happens

    Picture the charging chain: grid → chargepoint → cable → car's charge port → (onboard charger) → battery.

    • AC charging: AC travels all the way into the car; the onboard charger converts it.
    • DC charging: the chargepoint converts it; DC goes straight to the battery and the onboard charger is bypassed.

    Onboard chargers have to fit in the car, so they are much smaller than the converters in DC charging units.

    Traction battery pack (under the floor)Electric traction motorPower electronicsCharge port
    The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only.
  2. Level 1, Level 2 and DC fast

    The AFDC describes three levels:

    • Level 1: 120 V AC, about 1.9 kW – roughly 5 miles of range per hour; 8 hours adds about 40 miles for a mid-size EV
    • Level 2: 240 V (home) or 208 V (commercial), from 2.9 to 19.2 kW; most home units up to 30 A, about 7.2 kW – roughly 25 miles of range per hour
    • DC fast: up to 500 kW – roughly 100 to 200+ miles of range per 30 minutes

    As of 2023, nearly 80% of US public charging ports were Level 2 and more than 20% were DC fast.

  3. Connectors

    The AFDC lists the US connectors:

    • J1772: the standard plug on the vehicle end for Level 1 and Level 2 – all commercially available US EVs can charge on Level 1 and Level 2
    • CCS (SAE J1772 combo): the J1772 port with two extra pins below for DC fast charging; most EV models can use it
    • CHAdeMO: a DC fast connector common among Japanese makers
    • J3400 (NACS): based on one carmaker's design and being standardized by SAE; it works for all charging levels
  4. Power, voltage and current

    Charging power follows P = V × I (power = voltage × current).

    • A 230 V supply at 32 A gives 230 × 32 = 7,360 W, about 7.4 kW.
    • A battery at 400 V taking 125 A of DC receives 400 × 125 = 50,000 W = 50 kW.

    High charging power needs either high voltage, high current, or both. High current needs thick cables, which is why rapid chargers have heavy, often liquid-cooled cables.

  5. Charging time

    Charging time (hours) = energy needed (kWh) ÷ charging power (kW).

    To add 40 kWh at 7 kW takes 40 ÷ 7 ≈ 5.7 hours. At 50 kW it would take about 0.8 hours (48 minutes) – if the car could take 50 kW the whole time. Real times are a little longer because some energy is lost as heat in the charger and battery.

  6. Why charging slows down

    The battery management system protects the cells. As the battery fills, the cell voltages rise and the system reduces the current to avoid overcharging and overheating. So DC charging is fastest when the battery is fairly empty and slows down a lot near full.

    This is why rapid charging is usually quoted as time to reach about 80%, and why the AFDC says actual charging power varies by vehicle and battery state of charge. A cold battery also charges more slowly until it warms up.

  7. Safety

    Charging equipment is installed by licensed electricians; the AFDC notes residential Level 2 units need a dedicated 40-amp circuit under the National Electrical Code. The cable and connector are designed so no live pins can be touched, and power flows only after the car and charger have "talked" and agreed it is safe. Never use a damaged cable, and leave anything inside the car's high-voltage system to trained technicians.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Electric and hybrid vehicles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.