Inverters, converters and onboard chargers – Vehicles and Technology motor mechanics lesson
Lesson 4 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Meet the power electronics of an electric car: the inverter that drives the motor, the DC/DC converter that feeds the 12-volt side and the onboard charger that fills the battery from the mains – and see how they switch electricity thousands of times a second.
- Time
- 45 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
This topic is pure physics and diagrams. If you try the lamp activity, an adult should do the switching on an ordinary household lamp. Nothing in it involves a vehicle. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If power electronics were 100% efficient, what would change in the design of an electric car?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the wall box or cable charges the battery directly with AC. Batteries store DC. On AC charging, the onboard charger inside the car does the conversion.
- Thinking the inverter only works one way. During regenerative braking the inverter turns the motor's AC back into DC for the battery.
- Thinking power electronics stay cold because they have no moving parts. Switching losses produce heat, so the units are liquid-cooled.
Hands-on: Draw four boxes labelled "Mains AC", "Traction battery DC", "Motor three-phase AC" and "12 V DC". Draw arrows between them and write on each arrow which unit does the conversion: onboard charger, inverter, inverter in reverse (braking) and DC/DC converter. Then model pulse-width modulation with a desk lamp switched by an adult: count how many seconds out of every ten the lamp is on, and work out the "average" brightness as a percentage.
What you will learn
- I can explain the difference between AC and DC, and why an electric car needs both.
- I can say what the inverter, the DC/DC converter and the onboard charger each do.
- I can explain in simple terms how fast electronic switching turns DC into AC.
- I can use P = V × I to work out power, current and charging time.
- I can explain why power electronics get hot and need cooling.
Key words
- alternating current (AC)
- Current that keeps changing direction. Mains electricity is AC.
- direct current (DC)
- Current that flows one way only. Batteries store and supply DC.
- inverter
- Power electronics that turn the battery's DC into three-phase AC for the motor, controlling its frequency and size.
- rectifier
- A circuit that turns AC into DC.
- DC/DC converter
- Power electronics that change one DC voltage into another – in an electric car, high voltage down to about 12 volts.
- onboard charger
- The unit in the car that turns AC from a charging point into DC for the traction battery and controls the charge.
- transistor switch
- An electronic switch with no moving parts that can turn on and off thousands of times a second.
The big ideas
An electric car moves electrical energy around in different forms. The battery stores direct current (DC) at several hundred volts. The motor usually wants three-phase alternating current (AC) of changing frequency. The lights and computers want about 12 volts DC. And the mains supply at home is AC. Power electronics are the units that convert between these forms.
The US Department of Energy's Alternative Fuels Data Center (AFDC) lists three of them among an electric car's main components: the onboard charger, which takes incoming AC and converts it to DC to charge the traction battery while monitoring voltage, current, temperature and state of charge; the DC/DC converter, which turns high-voltage DC into the low-voltage DC needed to run accessories and recharge the auxiliary battery; and the power electronics controller, which manages the flow of energy from the battery and controls the motor's speed and torque. The heart of that controller is the inverter.
All of them work in the same basic way: very fast electronic switches chop the electricity up and rebuild it into the shape that is needed. Switching is efficient, but not perfect, so power electronics get warm and are usually cooled by liquid.
This is explanation for understanding, not a repair guide. Power electronics are high-voltage parts and are for trained technicians only.
Read-through: the teaching steps
Why convert at all?
Think of the car's electrical system as several countries with different currencies:
- Mains supply: AC (230 V in UK homes, 120 V or 240 V in US homes)
- Traction battery: DC, typically several hundred volts
- Traction motor: three-phase AC, frequency set by the required speed
- Lights, screens, control units: about 12 V DC
Each power electronics unit is an exchange desk between two of these.
Switching: the key idea
Power electronics use transistor switches that turn fully on or fully off thousands of times a second. A switch that is fully on or fully off wastes very little energy, which is why this method is efficient.
By changing how long the switch stays on in each cycle (pulse-width modulation), the circuit sets the average voltage. A switch on for half the time from a 400 V supply gives an average of about 200 V.
The inverter: DC to three-phase AC
The inverter has six switches arranged in three pairs, one pair for each phase of the motor. By opening and closing them in a careful pattern, it builds three smooth-looking alternating currents out of the battery's DC.
It controls two things: the frequency (which sets motor speed) and the size of the current (which sets torque). When braking, it runs in reverse, turning the motor's AC back into DC to recharge the battery.
The DC/DC converter
The DC/DC converter steps the high battery voltage down to about 12 V (some newer vehicles use 48 V for some systems). It keeps the auxiliary battery charged and runs the lights, wipers, heater fans and computers.
It does the job that an alternator does in a petrol car, but with no belt and no moving parts.
The onboard charger
For AC charging, the car's onboard charger first rectifies the incoming AC into DC, then controls the voltage and current going into the battery. The AFDC notes that it monitors voltage, current, temperature and state of charge as it works.
The onboard charger's power rating limits how fast the car can charge from AC. For DC rapid charging, the conversion is done in the large charging unit outside the car, which sends DC straight to the battery.
Heat and cooling
Even efficient switches lose a few per cent of the power as heat. At 100 kW, a loss of 3% is 3 kW – as much heat as a powerful electric fire. That is why power electronics are usually mounted on cooled plates with liquid running through them, part of the car's thermal system.
Safety: trained technicians only
Power electronics connect directly to the traction battery and may contain capacitors that hold charge for a while after switch-off. The UK Health and Safety Executive (HSE) lists residual voltage after switch-off among the hazards of electric vehicles and says high-voltage work needs isolating, locking off and proving dead by competent, trained people. Learners study these units from diagrams only.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electric and hybrid vehicles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do all-electric cars work?
- US Department of Energy, Alternative Fuels Data Center – Electric vehicle charging stations
- HSE – Electric and hybrid vehicles
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.