▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Bicycle lights, reflectors and the law – Vehicles and Technology motor mechanics lesson

Lesson 27 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how bicycle lights and reflectors work, how a hub dynamo powers lights, and exactly what UK rules say a bicycle needs after dark.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

A torch, a reflector and a dark room are all you need. Check the current rules for lights on GOV.UK before buying lights. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Should flashing lights be allowed on bicycles, or are steady lights better for drivers to judge? Why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking reflectors are enough on their own after dark. A reflector only works when a light shines on it; lights let the rider see and be seen by everyone.
  • Thinking a retroreflector is just a flat mirror. A flat mirror sends light away at an angle; corner cubes or beads send it straight back to the source.
  • Thinking a dynamo light must go out the moment the bike stops. Many dynamo lights have a capacitor that keeps them glowing for a few minutes.

Hands-on: In a dark room with an adult, shine a torch at a bicycle reflector from beside your eyes, then from the side, and compare how bright it looks. Then check a bicycle (with an adult) against the UK list: white front light, red rear light, red rear reflector, amber pedal reflectors on each pedal.

What you will learn

  • I can explain the difference between a light and a reflector.
  • I can explain how a retroreflector sends light back to its source.
  • I can use P = V × I and battery capacity to work out current and running time.
  • I can list what a bicycle needs between sunset and sunrise in the UK.

Key words

reflector
A device that sends light from headlamps back towards the driver, so the bicycle is seen.
retroreflector
A reflector built from tiny corner cubes or beads that returns light straight back to where it came from.
hub dynamo
A small electrical machine inside the front hub that makes electricity for lights as the wheel turns.
LED
Light-emitting diode: a very efficient electric light source.
lumen
A unit of how much light a lamp gives out.
to see and to be seen
The two jobs of bicycle lights: lighting the road ahead, and making the rider visible.

The big ideas

A cyclist at night has two problems: seeing the road, and being seen by drivers. Lights solve both; reflectors help with the second by returning other vehicles' headlight beams. Reflectors need no power, but they only work when light shines on them, so they are not a substitute for lights.

The Department for Transport's guidance on pedal cycle lighting says that between sunset and sunrise a bicycle on the road needs a white front light, a red rear light, a red rear reflector, and amber (yellow) reflectors on the front and back of each pedal (as of November 2026).

Modern bicycle lights almost all use LEDs, powered by batteries or by a hub dynamo built into the front wheel. This lesson explains how they work and what the rules require. Any wiring on a bicycle is low-voltage, but it is still checked by an adult or a bicycle mechanic.

Read-through: the teaching steps

  1. Lights and reflectors

    • A light makes its own light: it lets the rider see and be seen
    • A reflector returns light from someone else's lamp: it only helps the rider be seen, and only by people shining a light at it

    That is why rules ask for both. The bicycle drawing on the lesson page shows where they go.

    SaddleHandlebarsFramePedal and crankChainRear wheel and tyreFront wheelBrake
    The main parts of a bicycle.
  2. How a retroreflector works

    A mirror sends light off at an angle, away from the driver. A retroreflector is made of many tiny corner cubes (three mirrors at right angles) or glass beads. Light bounces off each face in turn and comes straight back towards its source – the driver's eyes are close to the headlamps, so they see the reflector glow.

  3. Pedal and wheel reflectors

    Reflectors that move – on pedals or spokes – are especially easy to spot, because the up-and-down movement of pedals or the turning of a wheel tells a driver at once that this is a bicycle.

  4. Batteries and LEDs

    LEDs turn much more of their electrical energy into light than old filament bulbs, so a small battery can run a bright lamp for hours.

    • Power: P = V × I
    • Running time ≈ battery capacity (mAh) ÷ current (mA)

    A light drawing 500 mA from a 2,000 mAh battery runs for about 2,000 ÷ 500 = 4 hours.

  5. Hub dynamos

    A hub dynamo has magnets and coils inside the front hub. As the wheel turns, the moving magnets make an alternating current in the coils – electromagnetic induction. A typical hub dynamo gives about 3 W at 6 V, enough for bright LED lights, with no batteries to run flat. Many lights have a capacitor that keeps them glowing for a few minutes when the bike stops.

  6. UK rules after dark

    Between sunset and sunrise, the DfT guidance says a bicycle on the road needs (as of November 2026):

    • A white front light
    • A red rear light
    • A red rear reflector
    • Amber/yellow pedal reflectors, front and back of each pedal

    Riders check GOV.UK for the current details.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.