Chains, sprockets and wear – Vehicles and Technology motor mechanics lesson
Lesson 26 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a bicycle roller chain is built, why it "stretches" as it wears, how worn chains damage sprockets, and how to calculate chain elongation as a percentage.
- Time
- 40 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
Hold the bicycle still while your child looks at the chain, and keep hands clear of it if the pedals are turned. No tools or chain removal are needed. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think racing cyclists might replace chains often, even though they are cheap compared with the rest of the bike?”
- Later: the homework, then the practice test.
Watch out for
- Thinking chain "stretch" means the steel plates stretch. The length grows because the pins and their holes wear; the plates themselves stay the same.
- Thinking more oil is always better. Excess oil picks up grit, which grinds the chain faster.
- Thinking a new chain will fix skipping on badly worn sprockets. Hooked sprocket teeth may make a new chain skip; worn parts are often replaced together.
Hands-on: With an adult, look at a bicycle chain while the bicycle is held still. Count the links between two marks and measure them with a ruler to see the ½-inch pitch. Look at the sprocket teeth: are they even or hooked? Do not turn the pedals while hands are near. Then make a paper chain of 24 links and see how adding 1 mm to each link changes the total length.
What you will learn
- I can name the parts of a roller chain.
- I can explain what chain "stretch" really is.
- I can calculate chain elongation as a percentage.
- I can explain why a worn chain wears the sprockets.
- I can explain why lubrication and keeping fingers clear both matter.
Key words
- pitch
- The distance from one pin to the next; on bicycle chains it is ½ inch (12.7 mm).
- roller
- The small turning cylinder that meets the sprocket teeth.
- pin
- The steel rod that joins the plates and acts as a hinge.
- elongation
- How much longer a chain has become through wear, often given as a percentage.
- lubrication
- A thin film of oil or wax that reduces friction and wear.
- chain guard
- A cover that stops fingers and clothes being caught by the chain.
The big ideas
The roller chain is one of the most efficient ways ever invented to pass power from one shaft to another. On a bicycle it links the chainring to the rear sprocket, and in good condition it wastes only a few per cent of the rider's effort.
Every link is made from inner and outer plates, pins, bushings (in many designs built into the inner plates) and rollers. All bicycle chains share the same ½-inch pitch, but they come in different widths to suit the number of gears.
As a chain is used, the pins and the holes they turn in wear. Each tiny bit of wear adds up along the chain, so it gets longer. People call this "stretch", although the steel is not stretching at all. A worn chain no longer fits the sprocket teeth properly and starts to wear them too. This lesson explains how and why, and how wear is measured as a percentage. Keep fingers away from a moving chain: it can trap and cut.
Read-through: the teaching steps
Parts of a chain
- Outer plates and inner plates: the side plates, alternating along the chain
- Pins: hinge the outer plates to the inner plates
- Rollers: turn on the inner links and roll onto the sprocket teeth
The pitch – pin to pin – is ½ inch (12.7 mm) on all modern bicycle chains, so 24 pitches measure 12 inches when new.
The main parts of a bicycle. Why chains get longer
Each pin turns a little every time the link bends round a sprocket – thousands of times per kilometre. Grit and dirt act like grinding paste. Microscopic wear at each pin adds up: 0.02 mm at each of 100 or more pins becomes several millimetres along the chain.
Measuring elongation
Elongation (%) = (measured length − new length) ÷ new length × 100
Over 24 pitches, a new chain measures 12 inches. If it measures 12 1/16 inches (12.0625), elongation = 0.0625 ÷ 12 × 100 ≈ 0.52%. Chain makers give the wear limit in their data, and mechanics use a chain-checker gauge or an accurate ruler to judge it.
How worn chains wear sprockets
A longer chain no longer matches the spacing of the sprocket teeth. Instead of sitting down between the teeth, the rollers ride up the faces of the teeth, loading only a few of them. The teeth wear into a hooked "shark-fin" shape. A new chain on badly worn sprockets may skip under load, so worn parts are often replaced together.
Lubrication
Oil or wax lets the pins turn with less friction and keeps water out, slowing wear and rust. Too much oil collects grit, which speeds up wear. A clean, lightly lubricated chain lasts longest.
Chain widths and gears
The more sprockets on the cassette, the closer they are packed, so the chain must be narrower. A single-speed chain is wide and robust; a chain for 11 or 12 sprockets is much slimmer. Chains must match the gears they are used with.
Safety
A moving chain can trap fingers, laces and loose trousers. In the US, the CPSC bicycle requirements require a chain guard on bicycles with a single front sprocket. When you look at a chain, an adult is with you, the bicycle is held still and nobody turns the pedals while your hands are near.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.