▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Bicycle lights, reflectors and the law – Vehicles and Technology motor mechanics lesson

Lesson 27 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how bicycle lights and reflectors work, how a hub dynamo powers lights, and what reflectors the CPSC requires on new bicycles sold in the US.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

A flashlight, a reflector and a dark room are all you need. Check your state's official site for the current rules on lights before buying lights. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Should flashing lights be allowed on bicycles, or are steady lights better for drivers to judge? Why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking reflectors are enough on their own after dark. A reflector only works when a light shines on it; lights let the rider see and be seen by everyone.
  • Thinking a retroreflector is just a flat mirror. A flat mirror sends light away at an angle; corner cubes or beads send it straight back to the source.
  • Thinking a dynamo light must go out the moment the bike stops. Many dynamo lights have a capacitor that keeps them glowing for a few minutes.

Hands-on: In a dark room with an adult, shine a flashlight at a bicycle reflector from beside your eyes, then from the side, and compare how bright it looks. Then check a bicycle (with an adult) against the CPSC reflector list: colorless front, red rear, pedal reflectors and wheel reflectors.

What you will learn

  • I can explain the difference between a light and a reflector.
  • I can explain how a retroreflector sends light back to its source.
  • I can use P = V × I and battery capacity to work out current and running time.
  • I can list the reflectors the CPSC requires on new bicycles, and explain that night-riding light rules are set by each state.

Key words

reflector
A device that sends light from headlamps back toward the driver, so the bicycle is seen.
retroreflector
A reflector built from tiny corner cubes or beads that returns light straight back to where it came from.
hub dynamo
A small electrical machine inside the front hub that makes electricity for lights as the wheel turns.
LED
Light-emitting diode: a very efficient electric light source.
lumen
A unit of how much light a lamp gives out.
to see and to be seen
The two jobs of bicycle lights: lighting the road ahead, and making the rider visible.

The big ideas

A cyclist at night has two problems: seeing the road, and being seen by drivers. Lights solve both; reflectors help with the second by returning other vehicles' headlight beams. Reflectors need no power, but they only work when light shines on them, so they are not a substitute for lights.

In the US, the CPSC bicycle requirements (16 CFR 1512) say new bicycles sold to the public must carry a colorless front reflector, a red rear reflector, pedal reflectors, and wheel (spoke) reflectors or reflective rims or tire sidewalls (as of November 2026). The rules for lights when riding at night are set by each state, so riders check their own state's law.

Modern bicycle lights almost all use LEDs, powered by batteries or by a hub dynamo built into the front wheel. This lesson explains how they work and what the rules require. Any wiring on a bicycle is low-voltage, but it is still checked by an adult or a bicycle mechanic.

Read-through: the teaching steps

  1. Lights and reflectors

    • A light makes its own light: it lets the rider see and be seen
    • A reflector returns light from someone else's lamp: it only helps the rider be seen, and only by people shining a light at it

    That is why rules ask for both. The bicycle drawing on the lesson page shows where they go.

    SaddleHandlebarsFramePedal and crankChainRear wheel and tireFront wheelBrake
    The main parts of a bicycle.
  2. How a retroreflector works

    A mirror sends light off at an angle, away from the driver. A retroreflector is made of many tiny corner cubes (three mirrors at right angles) or glass beads. Light bounces off each face in turn and comes straight back toward its source – the driver's eyes are close to the headlamps, so they see the reflector glow.

  3. Pedal and wheel reflectors

    Reflectors that move – on pedals or spokes – are especially easy to spot, because the up-and-down movement of pedals or the turning of a wheel tells a driver at once that this is a bicycle.

  4. Batteries and LEDs

    LEDs turn much more of their electrical energy into light than old filament bulbs, so a small battery can run a bright lamp for hours.

    • Power: P = V × I
    • Running time ≈ battery capacity (mAh) ÷ current (mA)

    A light drawing 500 mA from a 2,000 mAh battery runs for about 2,000 ÷ 500 = 4 hours.

  5. Hub dynamos

    A hub dynamo has magnets and coils inside the front hub. As the wheel turns, the moving magnets make an alternating current in the coils – electromagnetic induction. A typical hub dynamo gives about 3 W at 6 V, enough for bright LED lights, with no batteries to run flat. Many lights have a capacitor that keeps them glowing for a few minutes when the bike stops.

  6. US rules: reflectors and state law

    The CPSC (16 CFR 1512) requires these reflectors on new bicycles sold in the US (as of November 2026):

    • A colorless front reflector
    • A red rear reflector
    • Pedal reflectors
    • Wheel (spoke) reflectors, or reflective rims or tire sidewalls

    Rules about lights when riding at night are set by each state, so riders check their own state's law.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.