▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Working under vehicles: jacks, axle stands and lifts (theory) – Motor Vehicle Theory motor mechanics lesson

Lesson 3 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Understand why vehicles that are raised must be properly supported, what HSE says about jacks, axle stands and lifts, and the physics of the loads involved.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This is explanation for understanding, not a repair guide. The only activity uses the handbook and paper; learners never go under a raised vehicle. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think people still get trapped under vehicles, when the rule 'never rely on a jack alone' is so well known?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a good-quality jack is safe to work under. Any jack can lose pressure or roll. HSE says never rely on a jack alone.
  • Thinking weight is shared equally between the axles. Most cars carry more weight at the engine end, so stands at that end carry more.
  • Thinking any strong-looking object can be used as a support. Only proper stands, within their safe working load, at the lifting points.

Hands-on: With an adult, look at the vehicle handbook of a family car (not the car itself) and find the diagram that shows the jacking points. Copy it on paper and label the lifting points. Then draw a side view of a car on two axle stands and write the load on each stand for a 1,300 kg car with 60% of its weight at the front.

What you will learn

  • I can explain why a jack alone must never support a vehicle while someone is underneath.
  • I can list HSE's precautions for supporting a raised vehicle.
  • I can calculate axle loads and the load on each stand.
  • I can explain safe working load and why it must never be exceeded.
  • I can state the learner's rule: never go under a raised vehicle.

Key words

jack
A device for lifting a vehicle. It is not designed to hold the vehicle up while people work underneath.
axle stand
A fixed-height support placed under a manufacturer's lifting point to hold a raised vehicle.
lifting point
A strengthened point on the vehicle, specified by the manufacturer, for lifting and support.
safe working load (SWL)
The maximum load a piece of lifting or supporting equipment is rated to carry.
chock
A wedge placed against a wheel to stop the vehicle rolling.

The big ideas

This is explanation for understanding, not a repair guide. HSE says most deaths in motor vehicle repair happen when a person is trapped under an inadequately supported vehicle. A car weighs well over a tonne; if it falls, there is no time to move.

The key idea is simple: a jack lifts, but stands or a properly used lift support. HSE's guidance is to never rely on a jack alone, to work on hard, level ground, to chock the wheels left on the ground, to use the manufacturer's lifting points and the proper stand pins, and never to exceed the safe working load.

Learners never go under a raised vehicle. Watching such work is done from a safe place, with a qualified person in charge.

Read-through: the teaching steps

  1. Lifting and supporting are different jobs

    A trolley jack lifts by pumping hydraulic fluid into a cylinder. The load is held on fluid pressure, behind seals. A seal can leak, a release valve can be knocked, and a jack on wheels can roll. So a jack is a lifting tool only.

    An axle stand is a solid, fixed-height support locked with a pin. Placed correctly, it cannot slowly sink the way a jack can.

  2. HSE's precautions

    HSE lists these precautions for supporting vehicles:

    • do not rely on jacks alone – support on stands;
    • use only proper axle stand pins;
    • work on hard, level ground;
    • chock the wheels left on the ground;
    • use the manufacturer's lifting points;
    • never exceed the safe working load;
    • prop cabs, tipping bodies and air-suspended vehicles.

    They are listed so you understand the reasons, not as instructions.

  3. Where the weight goes

    A car's weight is not shared equally. With the engine at the front, a typical front-engined car carries more than half its weight on the front axle. When one end is raised, the stands under that end carry that axle's share, divided between them.

    Axle load = total mass × percentage on that axle. Load per stand = axle load ÷ number of stands.

  4. Safe working load

    Every jack, stand and lift is marked with a safe working load (SWL). Exceeding it can bend or collapse the equipment. A careful system leaves a margin: if the load is close to the SWL, a higher-rated item is needed. HSE says never exceed the safe working load.

  5. Why the ground and the wheels matter

    On soft ground a stand's small foot presses into the surface and can sink or tilt. On a slope the vehicle wants to roll, pulling it off its supports. Chocks on the wheels still on the ground resist that roll. Each precaution blocks a different way a vehicle can fall.

  6. The rules for learners

    • Never go under a raised vehicle.
    • Never use a jack, stand or lift unless trained and supervised.
    • Keep clear of vehicles being raised or lowered.
    • If you see a vehicle on a jack alone with someone underneath, tell a supervisor at once.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Workshop safety lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.