▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Risk assessment: hazards, risks and controls – Motor Vehicle Theory motor mechanics lesson

Lesson 2 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn how a workshop identifies hazards, judges risk by likelihood and severity, and chooses controls – from removing the hazard to PPE – using HSE's five steps.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains HSE's five-step method, dated November 2026. The activity uses paper only and an everyday setting. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “A risk matrix turns judgement into numbers. What are the advantages of that – and what could go wrong?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using 'hazard' and 'risk' as if they mean the same thing. A hazard is the thing that can harm; risk is how likely and how serious the harm is.
  • Reaching for PPE first. PPE is the last option. Remove, replace or redesign first.
  • Writing an assessment and never looking at it again. Controls must be reviewed, especially after changes or near misses.

Hands-on: Make a paper risk assessment for a familiar place – a school science lab, a kitchen or a bicycle workshop. List five hazards, score each for likelihood and severity (1–5), multiply, and suggest the best control for the top two using HSE's order. Do not try out any of the hazards.

What you will learn

  • I can distinguish between a hazard and a risk.
  • I can describe HSE's five steps for managing risk.
  • I can rank control measures, from removing the hazard to PPE.
  • I can use a likelihood × severity matrix to compare risks.
  • I can explain why assessments are recorded and reviewed.

Key words

hazard
Anything that may cause harm – for example a raised vehicle, petrol vapour or a slippery floor.
risk
How likely it is that someone will be harmed by a hazard, and how serious the harm could be.
control measure
An action that removes a hazard or reduces its risk.
reasonably practicable
Doing what is sensible to reduce risk, weighing the size of the risk against the time, effort and cost of controlling it.
residual risk
The risk that remains after controls are in place.

The big ideas

A risk assessment is simply a careful look at what could cause harm and what is being done about it. It is the backbone of workshop safety: every safe system of work, every guard and every item of PPE should trace back to one.

HSE's guidance gives five steps: identify hazards; assess the risks; control the risks; record your findings; review the controls. It stresses that you are not expected to remove every risk, only to do what is reasonably practicable – and that paperwork must never replace actually controlling the risks.

This lesson teaches the thinking behind risk assessment. It is theory for understanding: in a real workshop, assessments are made by competent people and learners work only under the supervision of a qualified person.

Read-through: the teaching steps

  1. Hazard and risk

    A hazard is something that may cause harm. Risk combines two questions:

    • How likely is it that someone will be harmed?
    • How serious would the harm be?

    A car on a properly used lift and a car on a jack alone are the same hazard – a heavy raised load – but the risks are very different.

  2. Step 1: identify hazards

    Walk the workshop and think about each task. HSE's motor vehicle repair guidance points to the big ones: vehicles that are lifted or supported, fuel and vapour, compressed air and tyres, hazardous substances such as used oil and brake dust, manual handling, slips and trips, and high-voltage systems on electric and hybrid vehicles. Ask the people who do the work – they know where the near misses happen.

  3. Step 2: assess the risks

    For each hazard decide who could be harmed and how, how likely it is and how serious it could be. Many workshops use a simple matrix:

    • likelihood 1 (very unlikely) to 5 (almost certain)
    • severity 1 (minor) to 5 (fatal)
    • risk score = likelihood × severity

    The score helps rank the risks, but any hazard that could kill always needs strong controls.

  4. Step 3: control the risks

    HSE lists options in this order – best first:

    • remove the hazard altogether;
    • redesign the job;
    • replace materials or processes with less hazardous ones;
    • reorganise work to reduce exposure;
    • practical safe-work measures;
    • personal protective equipment (PPE).

    PPE comes last because it protects only the wearer, and only when worn and fitted properly.

  5. Step 4: record your findings

    HSE says that if you employ 5 or more people you must record your significant findings: the hazards, who could be harmed and how, and the controls in place. Smaller businesses must still assess and control risks; they are simply not required to write it down.

  6. Step 5: review

    Controls must be checked to make sure they work. HSE says to review when controls may no longer be working, when changes could bring new risks – a new lift, a new type of vehicle – and after workers report problems, accidents or near misses. Then update the record.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Workshop safety lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.