▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Vehicle lifts: types, safe working load and examination – Motor Vehicle Theory motor mechanics lesson

Lesson 4 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Compare the main types of vehicle lift, and learn what safe working load means, why loads must be balanced and why lifts are thoroughly examined by a competent person.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains HSE guidance on lifts (and, for US readers, OSHA's 2014 interpretation), dated November 2026. Learners never operate lifts; the activity is a drawing. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Lifts make work much safer than lying on the floor – yet they also create new hazards. How would you weigh up the two?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a lift's safety locks make any placement safe. Locks hold the lift, not a badly placed vehicle. Pads must be on the lifting points and the load balanced.
  • Thinking that if the vehicle is lighter than the SWL, nothing else matters. Balance, lifting points and the condition of the lift all matter too.
  • Thinking a lift that works smoothly needs no examination. Wear can be hidden; HSE recommends thorough examination every 6 months.

Hands-on: Draw a side view of a car on a two-post lift on paper. Mark the centre of gravity with a cross between the posts. Then draw the same car with the engine removed and move the cross to show where the centre of gravity goes. Write a sentence explaining why this could make the car tip.

What you will learn

  • I can describe two-post, four-post and scissor lifts.
  • I can explain safe working load and calculate how much of it is used.
  • I can explain why removing heavy parts can unbalance a vehicle on a lift.
  • I can state HSE's recommendation for thorough examination of lifts.
  • I can explain why learners never operate lifts or stand under raised vehicles.

Key words

two-post lift
A lift with two columns and swinging arms whose pads go under the vehicle's lifting points.
four-post lift
A lift with two runways; the vehicle is driven on and rests on its wheels.
scissor lift
A lift raised by criss-cross arms under a platform or pads.
safe working load (SWL)
The maximum load the lift is rated to carry.
thorough examination
A detailed check by a competent person to find wear or damage that could make the lift unsafe.
centre of gravity
The point where the weight of an object can be thought of as acting.

The big ideas

A vehicle lift lets trained technicians stand upright under a car instead of lying on the floor. It is one of the most useful pieces of workshop equipment – and, misused, one of the most dangerous, because it holds more than a tonne of metal above people's heads.

HSE's guidance is clear: use the manufacturer's lifting points, never exceed the safe working load, engage the arm locks and place the pads correctly on two-post lifts, balance the load – especially when heavy parts are removed – and have lifts thoroughly examined by a competent person, which HSE recommends every 6 months.

This lesson explains how lifts work and why these rules exist. It is theory for understanding: learners never operate a lift and never stand under a raised vehicle.

Read-through: the teaching steps

  1. Types of lift

    • Two-post lift – two columns with swinging arms; pads go under the lifting points. The wheels hang free, so wheels and brakes can be reached.
    • Four-post lift – two runways; the vehicle is driven on and rests on its wheels. Good for underbody inspection.
    • Scissor lift – criss-cross arms raise a platform or pads; often low-profile.
    • In-ground and mobile column lifts are also used, especially for heavier vehicles.
  2. How they lift

    Most lifts use hydraulic rams or electric motors driving screws or chains. Good designs have mechanical safety locks that engage as the lift rises, so the load is held even if hydraulic pressure is lost. Technicians lower the lift onto its locks before working beneath it – but the locks only help if the vehicle is correctly placed in the first place.

  3. Safe working load

    Every lift is marked with its safe working load. HSE says never exceed it.

    Percentage of SWL used = vehicle mass ÷ SWL × 100.

    A heavy van on a lift meant for small cars may exceed the rating, and the lift's arms or pads may not reach the van's lifting points correctly.

  4. Balance and the centre of gravity

    A vehicle is placed so its centre of gravity sits between the posts or on the runways. On a two-post lift this matters most.

    If a heavy part such as an engine or gearbox is removed, the centre of gravity moves away from that end. A vehicle that was balanced can now tip. HSE specifically warns to balance the load when heavy parts are removed. Workshops use the vehicle data and support stands designed for this.

  5. Arm locks and pads

    On a two-post lift HSE says arm locks must be engaged and pads correctly placed. If an arm swings, its pad can slide off the lifting point. The manufacturer's lifting points are strengthened to carry the load; anywhere else the body can bend and the vehicle can shift.

  6. Thorough examination

    Wear in cables, chains, locks, pivots and hydraulics can build up unseen. HSE recommends a thorough examination every 6 months by a competent person, as well as routine checks by trained users. Faults found must be put right before the lift is used again.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Workshop safety lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.