Working under vehicles: jacks, axle stands and lifts (theory) – Motor Vehicle Theory motor mechanics lesson
Lesson 3 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Understand why vehicles that are raised must be properly supported, what HSE says about jacks, axle stands and lifts, and the physics of the loads involved.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This is explanation for understanding, not a repair guide. The only activity uses the handbook and paper; learners never go under a raised vehicle. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think people still get trapped under vehicles, when the rule 'never rely on a jack alone' is so well known?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a good-quality jack is safe to work under. Any jack can lose pressure or roll. HSE says never rely on a jack alone.
- Thinking weight is shared equally between the axles. Most cars carry more weight at the engine end, so stands at that end carry more.
- Thinking any strong-looking object can be used as a support. Only proper stands, within their safe working load, at the lifting points.
Hands-on: With an adult, look at the vehicle handbook of a family car (not the car itself) and find the diagram that shows the jacking points. Copy it on paper and label the lifting points. Then draw a side view of a car on two axle stands and write the load on each stand for a 1,300 kg car with 60% of its weight at the front.
What you will learn
- I can explain why a jack alone must never support a vehicle while someone is underneath.
- I can list HSE's precautions for supporting a raised vehicle.
- I can calculate axle loads and the load on each stand.
- I can explain safe working load and why it must never be exceeded.
- I can state the learner's rule: never go under a raised vehicle.
Key words
- jack
- A device for lifting a vehicle. It is not designed to hold the vehicle up while people work underneath.
- axle stand
- A fixed-height support placed under a manufacturer's lifting point to hold a raised vehicle.
- lifting point
- A strengthened point on the vehicle, specified by the manufacturer, for lifting and support.
- safe working load (SWL)
- The maximum load a piece of lifting or supporting equipment is rated to carry.
- chock
- A wedge placed against a wheel to stop the vehicle rolling.
The big ideas
This is explanation for understanding, not a repair guide. British safety guidance from HSE says most deaths in motor vehicle repair happen when a person is trapped under an inadequately supported vehicle. A car weighs well over a ton; if it falls, there is no time to move.
The key idea is simple: a jack lifts, but stands or a properly used lift support. The guidance is to never rely on a jack alone, to work on hard, level ground, to chock the wheels left on the ground, to use the manufacturer's lifting points and the proper stand pins, and never to exceed the safe working load. In the US, OSHA has no specific standard for automotive lifts, but its General Duty Clause still requires a workplace free from recognized hazards.
Learners never go under a raised vehicle. Watching such work is done from a safe place, with a qualified person in charge.
Read-through: the teaching steps
Lifting and supporting are different jobs
A trolley jack lifts by pumping hydraulic fluid into a cylinder. The load is held on fluid pressure, behind seals. A seal can leak, a release valve can be knocked, and a jack on wheels can roll. So a jack is a lifting tool only.
An axle stand is a solid, fixed-height support locked with a pin. Placed correctly, it cannot slowly sink the way a jack can.
HSE's precautions
HSE lists these precautions for supporting vehicles:
- do not rely on jacks alone – support on stands;
- use only proper axle stand pins;
- work on hard, level ground;
- chock the wheels left on the ground;
- use the manufacturer's lifting points;
- never exceed the safe working load;
- prop cabs, tipping bodies and air-suspended vehicles.
They are listed so you understand the reasons, not as instructions.
Where the weight goes
A car's weight is not shared equally. With the engine at the front, a typical front-engined car carries more than half its weight on the front axle. When one end is raised, the stands under that end carry that axle's share, divided between them.
Axle load = total mass × percentage on that axle. Load per stand = axle load ÷ number of stands.
Safe working load
Every jack, stand and lift is marked with a safe working load (SWL). Exceeding it can bend or collapse the equipment. A careful system leaves a margin: if the load is close to the SWL, a higher-rated item is needed. HSE says never exceed the safe working load.
Why the ground and the wheels matter
On soft ground a stand's small foot presses into the surface and can sink or tilt. On a slope the vehicle wants to roll, pulling it off its supports. Chocks on the wheels still on the ground resist that roll. Each precaution blocks a different way a vehicle can fall.
Lifts and the law in the US
OSHA's 2014 interpretation letter says no specific OSHA standard applies to automotive lifts, but employers must still keep the workplace free from recognized hazards under the General Duty Clause. ANSI/ALI ALOIM:2008 is the recognized industry standard for operating, inspecting and maintaining lifts.
For learners the rules are the same everywhere: never go under a raised vehicle, never operate lifting equipment unless trained and supervised, and keep clear while a vehicle is raised or lowered.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Workshop safety lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
About this lesson
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.