▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Parking brakes: mechanical and electric – Motor Vehicle Theory motor mechanics lesson

Lesson 70 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how lever-and-cable and electric parking brakes hold a parked vehicle, why they must work mechanically, and how to calculate the force needed to hold a car on a slope.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains mechanical and electric parking brakes with force calculations. It is theory only; brake work is for trained technicians. Inspection details are dated November 2026. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Electric parking brakes free up space between the front seats. What else do you think they make possible that a lever cannot?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the parking brake works through the brake fluid. It must hold mechanically, through cables, levers or a screw.
  • Forgetting to share the lever force between two cables. The equaliser divides the pull between the left and right brakes.
  • Using mass instead of weight in the slope formula. Weight = m × g, in newtons.

Hands-on: Make a ratchet model from card: cut a strip with saw-tooth notches and a card flap pinned so it drops into the notches. Show how it lets the strip move one way only, and how lifting the flap releases it. Then measure a slope (for example a ramp) with a ruler: rise ÷ length × 100 gives its gradient. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look, for example at the parking brake switch or lever.

What you will learn

  • I can describe how a lever-and-cable parking brake works.
  • I can describe how an electric parking brake applies and holds the brakes.
  • I can explain why a parking brake must hold mechanically.
  • I can calculate cable forces, weight, holding force on a slope and parking brake efficiency.

Key words

parking brake
A brake that holds a parked vehicle still mechanically. In the UK often called the handbrake.
ratchet and pawl
A toothed bar and a spring-loaded catch that hold a lever in position.
equaliser
A part that shares the cable pull equally between the two brakes.
electric parking brake (EPB)
A parking brake applied by electric motors controlled by a switch and a control unit.
gradient
The steepness of a slope; a 20% gradient rises 20 m for every 100 m along.

The big ideas

This is explanation for understanding, not a repair guide. Parking brakes are part of the braking system, which is safety-critical; only trained technicians work on them.

A car's foot brake is hydraulic, but a parked car may be left for days, and hydraulic pressure could leak away. So every car also has a parking brake that holds mechanically. Older and simpler cars use a lever and cables; many newer cars use an electric parking brake worked by a switch.

The MOT inspection manual (section 1, as of November 2026) tests it: most cars must reach a parking brake efficiency of at least 16%, and an EPB warning lamp showing a malfunction is a Major defect.

Read-through: the teaching steps

  1. Lever and cables

    Pulling the lever (or pressing a foot pedal on some vehicles) pulls a cable. An equaliser shares the pull between the cables to the two rear brakes. A ratchet and pawl hold the lever; a button releases it.

    • Rear drums: a lever inside the drum spreads the shoes.
    • Rear discs: a lever on the caliper turns a screw or cam that pushes the piston, or a small drum-in-hat brake inside the disc is used.
  2. Forces in the system

    Force at each cable = driver's pull × lever ratio ÷ number of cables (ignoring friction in the cables). Cables stretch and wear over time, so systems are adjusted as the manufacturer describes, by a technician.

  3. Electric parking brakes

    A switch sends a request to a control unit. Electric motors, usually on the rear calipers, drive a gearbox and a screw that push the piston and pads against the disc. The screw does not run backwards, so the brake stays on when the motor stops. Some systems instead use a motor that pulls conventional cables.

    • EPBs may apply automatically, for example when the ignition is switched off.
    • Many release automatically when the driver moves off and give hill-hold.
  4. Why mechanical holding matters

    The MOT inspection manual says EPBs "must be maintained in operation by direct mechanical means", usually hidden in the calliper or motor gear assembly. It treats a parking brake that works only hydraulically, on a vehicle first used on or after 1 January 1968, as a Major defect.

  5. Holding on a slope

    The force needed to stop a vehicle rolling is the part of its weight acting down the slope:

    F = m × g × sin θ

    For a gradient given as a percentage, sin θ ≈ gradient ÷ 100 for gentle slopes (a 20% gradient has sin θ = 0.196). Parking brake efficiency = parking brake force ÷ weight × 100.

  6. Checks and faults

    In the MOT (section 1, as of November 2026): parking brake efficiency below 16% = Major; below half of that = Dangerous; ratchet not holding = Major; EPB malfunction lamp = Major.

    Common faults in theory: stretched or seized cables, worn ratchets, seized caliper mechanisms, and EPB motor or electrical faults. Drivers should always use the parking brake when parked, as the vehicle handbook explains.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.