Parking brakes: mechanical and electric – Motor Vehicle Theory motor mechanics lesson
Lesson 70 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how lever-and-cable and electric parking brakes hold a parked vehicle, why they must work mechanically, and how to calculate the force needed to hold a car on a slope.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson explains mechanical and electric parking brakes with force calculations. It is theory only; brake work is for trained technicians. Inspection details are dated November 2026. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Electric parking brakes free up space between the front seats. What else do you think they make possible that a lever cannot?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the parking brake works through the brake fluid. It must hold mechanically, through cables, levers or a screw.
- Forgetting to share the lever force between two cables. The equalizer divides the pull between the left and right brakes.
- Using mass instead of weight in the slope formula. Weight = m × g, in newtons.
Hands-on: Make a ratchet model from card: cut a strip with saw-tooth notches and a card flap pinned so it drops into the notches. Show how it lets the strip move one way only, and how lifting the flap releases it. Then measure a slope (for example a ramp) with a ruler: rise ÷ length × 100 gives its gradient. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look, for example at the parking brake switch or lever.
What you will learn
- I can describe how a lever-and-cable parking brake works.
- I can describe how an electric parking brake applies and holds the brakes.
- I can explain why a parking brake must hold mechanically.
- I can calculate cable forces, weight, holding force on a slope and parking brake efficiency.
Key words
- parking brake
- A brake that holds a parked vehicle still mechanically. In the UK often called the parking brake.
- ratchet and pawl
- A toothed bar and a spring-loaded catch that hold a lever in position.
- equalizer
- A part that shares the cable pull equally between the two brakes.
- electric parking brake (EPB)
- A parking brake applied by electric motors controlled by a switch and a control unit.
- gradient
- The steepness of a slope; a 20% gradient rises 20 m for every 100 m along.
The big ideas
This is explanation for understanding, not a repair guide. Parking brakes are part of the braking system, which is safety-critical; only trained technicians work on them.
A vehicle's foot brake is hydraulic, but a parked vehicle may be left for days, and hydraulic pressure could leak away. So every vehicle also has a parking brake that holds mechanically. Older and simpler vehicles use a lever or pedal and cables; many newer vehicles use an electric parking brake worked by a switch.
Vehicle safety inspections are set by each state; Virginia's inspection, for example, includes the parking brake.
Read-through: the teaching steps
Lever and cables
Pulling the lever (or pressing a foot pedal on some vehicles) pulls a cable. An equalizer shares the pull between the cables to the two rear brakes. A ratchet and pawl hold the lever; a button releases it.
- Rear drums: a lever inside the drum spreads the shoes.
- Rear discs: a lever on the caliper turns a screw or cam that pushes the piston, or a small drum-in-hat brake inside the rotor is used.
Forces in the system
Force at each cable = driver's pull × lever ratio ÷ number of cables (ignoring friction in the cables). Cables stretch and wear over time, so systems are adjusted as the manufacturer describes, by a technician.
Electric parking brakes
A switch sends a request to a control unit. Electric motors, usually on the rear calipers, drive a transmission and a screw that push the piston and pads against the rotor. The screw does not run backward, so the brake stays on when the motor stops. Some systems instead use a motor that pulls conventional cables.
- EPBs may apply automatically, for example when the ignition is switched off.
- Many release automatically when the driver moves off and give hill-hold.
Why mechanical holding matters
Because hydraulic pressure can leak away, the hold must be mechanical: cables, levers, a cam or a screw. A parking brake that relied only on hydraulic pressure could release while the vehicle is parked.
Holding on a slope
The force needed to stop a vehicle rolling is the part of its weight acting down the slope:
F = m × g × sin θ
For a gradient given as a percentage, sin θ ≈ gradient ÷ 100 for gentle slopes (a 20% gradient has sin θ = 0.196). Parking brake efficiency = parking brake force ÷ weight × 100.
Checks and faults
Common faults in theory: stretched or seized cables, worn ratchets, seized caliper mechanisms, and EPB motor or electrical faults, often shown by a warning light.
Drivers should always set the parking brake when parked, as the owner's manual explains. A technician diagnoses and repairs parking brake faults.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.