▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

ABS, traction control and stability control – Motor Vehicle Theory motor mechanics lesson

Lesson 71 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how anti-lock brakes keep the wheels turning under hard braking, how traction control stops wheelspin, and how stability control brakes individual wheels to keep a car on the line the driver is steering.

Time
50 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains ABS, traction control and stability control with slip and yaw calculations. Rules quoted are dated November 2026. It is theory only; these safety systems are diagnosed and repaired by trained technicians. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Stability control can save lives, but some people say it makes drivers less careful. What do you think?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking ABS always shortens stopping distances. Its main job is to keep steering control. On loose surfaces it may not shorten the distance.
  • Dividing by wheel speed when working out slip. Divide by the vehicle speed.
  • Mixing up oversteer and understeer. Oversteer: turns too much (rear slides). Understeer: turns too little (front slides).

Hands-on: Slide an eraser across a table while pushing it (sliding, like a locked wheel), then roll a coin across the same table and try to steer it with a finger: the rolling coin changes direction easily, the sliding eraser does not. Draw a car on a bend showing understeer and oversteer paths and mark which wheel ESC would brake in each case. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look, for example at the ABS symbol on the dashboard.

What you will learn

  • I can explain wheel slip and why a locked wheel cannot steer.
  • I can describe how ABS senses and controls wheel locking.
  • I can explain how traction control and stability control work, including oversteer and understeer.
  • I can calculate slip percentage, wheel surface speed and expected yaw rate.

Key words

ABS
Anti-lock braking system: stops wheels locking under hard braking.
slip
How much slower the tyre surface moves than the vehicle, as a percentage. 0% is free rolling; 100% is a locked wheel.
yaw rate
How fast the vehicle turns about a vertical axis, in rad/s.
oversteer
The rear slides out and the car turns more than the driver intends.
understeer
The front tyres lose grip and the car turns less than the driver intends.

The big ideas

This is explanation for understanding, not a repair guide. These are safety systems; only trained technicians with diagnostic equipment work on them.

Tyres give their best grip when they are rolling with a little slip. If a wheel locks under braking, the tyre slides, grip falls and the wheel can no longer steer. Anti-lock brakes prevent this by releasing and reapplying the pressure at each wheel many times a second.

The same sensors and valves allow traction control (stopping wheelspin) and electronic stability control (braking individual wheels to keep the car on course). Highway Code rule 120 advises following the vehicle handbook and not assuming a car with ABS will stop in a shorter distance. The MOT inspection manual (section 1, as of November 2026) classes all ABS defects as Major.

Read-through: the teaching steps

  1. Slip and grip

    Slip = (vehicle speed − wheel surface speed) ÷ vehicle speed × 100.

    A free-rolling wheel has 0% slip; a locked wheel has 100%. Grip usually rises with slip up to a peak at a small slip (typically roughly 10–20% on dry roads) and then falls. A sliding tyre also gives almost no sideways grip, so it cannot steer. Wheel surface speed v = 2π × r × N ÷ 60.

  2. How ABS works

    • Wheel speed sensors at each wheel send pulses to the control unit.
    • If a wheel slows much faster than the car could, it is about to lock.
    • A hydraulic modulator between the master cylinder and the wheels can hold, release and reapply pressure to that wheel.
    • A pump returns released fluid. The cycle repeats many times a second, and the driver feels the pedal pulse.

    If the ABS has a fault, a warning light comes on and normal braking usually remains.

  3. Traction control

    When accelerating, if a driven wheel spins faster than the others, the system:

    • brakes the spinning wheel, which lets the differential send torque to the other wheel; and/or
    • asks the engine control unit to reduce torque.

    This helps moving off on ice, wet roads or loose surfaces.

  4. Stability control

    FMVSS 126 defines ESC as a computer-controlled system that brakes individual wheels to limit oversteer and understeer, determines the vehicle's yaw rate and estimates its side slip, monitors driver steering inputs and can modify engine torque. It works over the full speed range except at very low speed (below 20 km/h, 12.4 mph), in reverse and during start-up.

    • Understeer (turning too little): brake the inner rear wheel and cut torque.
    • Oversteer (turning too much): brake the outer front wheel.
  5. Expected yaw rate

    The control unit compares what the driver asks for with what the car is doing. A simple estimate of the yaw rate a car should have on a curve is v ÷ R (speed ÷ radius). If the measured yaw rate is much higher, the car is oversteering; much lower, it is understeering.

  6. Using and checking the systems

    Highway Code rule 120: if the car has ABS, follow the advice in the vehicle handbook; do not assume ABS will stop the car in a shorter distance. ABS keeps steering control but cannot beat the limits of grip.

    MOT (section 1, as of November 2026): all ABS defects are Major, including a warning device that does not work or shows a malfunction, and damaged wheel speed sensors or wiring. ABS must not be removed or disabled on a vehicle first used on or after 1 January 2010. ESC is not part of section 1.

The lesson, step by step

50 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task15 minNot assessed, self-checked
Worked examples and guided practice10 minMarked by Classfern
Independent practice (three levels)16 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.