▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Brake servos (boosters) – Motor Vehicle Theory motor mechanics lesson

Lesson 69 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how a brake servo uses vacuum or an electric motor to multiply the driver's pedal force, why it needs a pump on diesel and electric cars, and how to calculate the force it adds.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains how brake assistance works, with pressure and force calculations. It is theory only; brakes are safety-critical and are worked on only by trained technicians. Inspection details are dated November 2026. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Electric cars make regenerative braking and friction braking work together. Why might brake-by-wire make this easier than a vacuum servo?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the servo pushes using brake fluid. A vacuum servo works with air pressure on a diaphragm; the master cylinder then makes the hydraulic pressure.
  • Thinking the brakes stop working if the servo fails. They still work but need much more pedal force.
  • Using kPa in F = Δp × A with A in m². Change kPa to Pa (× 1,000) to get newtons.

Hands-on: Press a rubber sink plunger onto a smooth table and try to pull it straight off: the air pressure pushing it down is the same kind of force a servo uses. Calculate the force on a circle the size of the plunger if the pressure difference were 50 kPa (F = Δp × πr²). Draw the servo at rest and in use, showing vacuum and air. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look: for example, find the round servo behind the brake master cylinder.

What you will learn

  • I can explain how a vacuum servo uses a pressure difference to add force.
  • I can explain where the vacuum comes from on petrol, diesel and electric vehicles.
  • I can calculate servo force from pressure difference and diaphragm area, and the boost ratio.
  • I can describe electric assistance and brake-by-wire, and why assistance faults are serious.

Key words

servo
A device that adds force to the driver's pedal push.
diaphragm
A flexible disc in the servo that is pushed by the difference in air pressure on its two sides.
manifold vacuum
The low pressure in a petrol engine's intake when the throttle is partly closed.
boost ratio
Total force on the master cylinder ÷ the driver's force.
brake-by-wire
A system in which the pedal sends a signal and an electrically powered unit makes the brake pressure.

The big ideas

This is explanation for understanding, not a repair guide. Brakes are safety-critical; only trained technicians work on them.

Without help, a driver would need to press the brake pedal very hard to stop a modern car quickly. A brake servo (called a booster in the USA) adds force between the pedal and the master cylinder. Most use the difference between atmospheric pressure and the vacuum in the engine's intake; some use a vacuum pump; many newer cars use an electric motor.

The MOT inspection manual (section 1, as of November 2026) checks servo operation: a defective or ineffective servo is a Major defect and an inoperative one is Dangerous. It also notes that many modern vehicles use electric assistance or brake-by-wire instead of a vacuum servo.

Read-through: the teaching steps

  1. Pressure difference makes force

    Force = pressure difference × area (F = Δp × A, with Δp in pascals and A in m²).

    Atmospheric pressure is about 101 kPa. If one side of a large diaphragm has a vacuum of, say, 40 kPa absolute and the other has air at 101 kPa, the difference of 61 kPa on a diaphragm of 0.04 m² gives about 2,400 N. A large diaphragm makes a large force from a modest pressure difference.

  2. Inside a vacuum servo

    • A large round housing between the pedal and the master cylinder, split by a diaphragm.
    • At rest, both chambers hold vacuum, so there is no force.
    • Pressing the pedal moves a control valve that shuts off the vacuum to the rear chamber and lets in atmospheric air.
    • The pressure difference pushes the diaphragm and pushrod forward, adding to the driver's force.
    • The valve balances so the extra force stays in proportion to the pedal force, keeping good feel.
  3. Where the vacuum comes from

    • Petrol engines: the intake manifold, through a hose with a one-way valve.
    • Diesel engines: little manifold vacuum because power is controlled by fuel, not throttle, so a mechanical or electric vacuum pump is used.
    • Electric cars: no intake at all, so an electric vacuum pump or electric servo is used.

    The one-way valve keeps stored vacuum for a few applications if the supply drops.

  4. Electric assistance and brake-by-wire

    An electric servo uses a motor and gears to push the master cylinder, with sensors measuring the pedal. Brake-by-wire goes further: the pedal mainly sends a signal and an electric unit makes the pressure. These systems work without vacuum and can blend friction braking with regenerative braking in hybrids and EVs, where the motor works as a dynamo. With electric systems a constant pedal resistance can be normal.

  5. Assistance faults in theory

    • Hard pedal with the engine running: possible loss of vacuum (split hose, faulty valve, pump fault) or a servo fault.
    • Hissing when the pedal is pressed: possible air leak in the servo.
    • Warning light on electric systems: a fault stored by the control unit.

    The brakes still work without assistance but need far more force. A technician diagnoses these faults; drivers should not continue to drive a car with a brake fault.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.