▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Tread depth and the law – Garage Basics motor mechanics lesson

Lesson 44 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out why tyre tread matters, what the UK legal minimum tread depth is for cars and motorcycles, and how tread depth is measured.

Time
40 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

Please do the measuring yourself while your child watches. Keep the car parked and switched off. The legal figures in this lesson come from GOV.UK. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think worn tyres are much more dangerous on a wet road than on a dry one?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking 1.6 mm is a safe target. It is the legal minimum. Wet grip falls as tread wears, so many drivers replace tyres before reaching it.
  • Thinking tread only needs checking in one place. The law covers the central three-quarters all the way round, so the tyre must be checked in several places.
  • Thinking a motorcycle has the same limit as a car. GOV.UK gives 1 mm for motorcycles and 1.6 mm for cars.

Hands-on: Cut a piece of thick card into a "tyre" and draw a tread pattern. Mark the central three-quarters. Then, with an adult, look at the tyres of a parked, switched-off car without touching them if they could be hot: find the small tread wear indicator bars in the grooves. If the adult has a tread depth gauge, watch them measure in three places.

What your child will learn

  • I can explain how tread grooves help a tyre grip on a wet road.
  • I can state the UK minimum tread depth for cars and for motorcycles.
  • I can explain where on the tyre the tread depth is measured.
  • I can calculate the usable tread on a tyre and the width of the central three-quarters.

Key words

tread
The patterned outer surface of a tyre that touches the road.
groove
A channel in the tread that carries water away from under the tyre.
aquaplaning
When a layer of water builds up under the tyre so it rides on the water and loses grip. It is also called hydroplaning.
tread depth gauge
A small measuring tool with a probe that measures how deep the grooves are.
tread wear indicator
Small raised bars across the bottom of the main grooves. When the tread wears down level with them, the tyre is at or near its limit.

The big ideas

Tread is the patterned rubber on the outside of a tyre. On a dry road, a smooth tyre grips well. On a wet road the grooves matter: they act like channels, squeezing water out from under the tyre so the rubber can touch the road. As tread wears, the grooves get shallower and can carry less water. At speed, water can build up under the tyre so it rides on a film of water: aquaplaning. Steering and braking then almost stop working.

The UK has a legal minimum. GOV.UK states that for cars, light vans and light trailers the tread must be at least 1.6 mm deep across the middle three-quarters of the tread and around the entire circumference. For motorcycles, large vehicles and passenger-carrying vehicles it is 1 mm, and mopeds must have visible tread. The MOT inspection manual treats tread below the requirement on a car as a Dangerous defect, which is a fail. Driving a vehicle in a dangerous condition can lead to a fine, penalty points and a driving ban.

Tyres can be checked with a tread depth gauge, and many tyres have tread wear indicators: small bars in the grooves that show when the tread is near the limit. Many drivers change tyres well before the legal minimum, because wet grip falls as tread wears. Tyre fitting is done by trained technicians.

Read-through: the teaching steps

  1. What tread does

    On a wet road, the grooves carry water out from under the tyre so the rubber can press on the road. Deep grooves can carry a lot of water; shallow grooves carry little. That is why worn tyres grip much less in the wet and make stopping distances longer.

    Tread depthat least 1.6 mmCentral three-quarters of the treadTread blockGroove
    Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round.
  2. Aquaplaning

    If more water arrives than the grooves can carry away, a wedge of water lifts the tyre off the road. The car can no longer be steered or braked properly. Higher speed, deeper water and less tread all make it more likely.

  3. The UK legal minimum

    GOV.UK: cars, light vans and light trailers need at least 1.6 mm of tread across the middle three-quarters of the tread and around the entire circumference. Motorcycles, large vehicles and passenger-carrying vehicles need 1 mm; mopeds need visible tread. In the MOT inspection manual for cars, the outer quarters can be devoid of tread.

  4. Where to measure

    Divide the width of the tread into four equal strips. The central three-quarters are the middle three strips. The tread must meet the minimum all the way across that central band and all the way round the tyre, so a technician checks in several places.

  5. Measuring tread

    A tread depth gauge has a probe that slides into the groove and shows the depth in millimetres. Tread wear indicators, small bars moulded across the bottom of the main grooves, show when the tread is close to 1.6 mm.

  6. Usable tread

    A new car tyre typically has around 8 mm of tread. Only the tread above the legal limit is usable: 8 − 1.6 = 6.4 mm. If a tyre wears 1 mm for every so many miles, you can estimate how long it will last.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Wheels and tyres lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.