▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Tires, fuel economy and rolling resistance – Vehicles and Technology motor mechanics lesson

Lesson 48 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Discover why a tire wastes energy every time it rolls, how much under-inflation costs in fuel, and how engineers balance low rolling resistance against grip.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson is for curious learners of 14 and over. The math uses weight = mass × 10 and simple percentages; a calculator is fine. Real tire checks should be done by an adult. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If correctly inflated tires save fuel and make cars safer, why do you think so many tires on the road are under-inflated? How could cars or fuel stations make checking easier?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using the maximum pressure printed on the tire wall as the pressure to inflate to. That is the most the tire can safely hold. The correct pressure comes from the car maker, in the handbook or on the label in the door frame.
  • Checking pressure straight after a long drive. Warm tires read higher. Check when the tires are cold for a true reading.
  • Thinking rolling resistance is friction between the tire and the road. Grip (friction) is what lets the car steer and brake. Rolling resistance comes mainly from the rubber squashing and recovering, which turns energy into heat.

Hands-on: Roll a ball test: on a smooth floor or a long table, build a ramp from a book and a piece of card. Roll a well-pumped football or basketball down it and mark how far it travels. Let a little air out (with an adult) and roll it again from the same point. Which goes further, and why? Squeeze each ball to feel how much it flattens. You can also look – without touching the valve – at the tire pressure label inside a parked car's door frame with an adult.

What you will learn

  • I can explain what rolling resistance is and where the lost energy goes.
  • I can calculate a rolling resistance force from a car's weight and a coefficient.
  • I can work out the effect of under-inflation on fuel economy using a percentage per psi.
  • I can explain why correct tire pressure matters for economy, wear and safety.
  • I can describe the trade-off between low rolling resistance and grip.

Key words

rolling resistance
The force that resists a tire rolling, caused mainly by the rubber squashing and recovering as it turns.
hysteresis
Energy lost as heat when a material is squashed and springs back; the main cause of rolling resistance.
coefficient of rolling resistance
A number that compares the rolling resistance force with the weight on the tire. For car tires it is typically around 0.01.
contact patch
The small area of tire actually touching the road at any moment.
psi
Pounds per square inch, a unit of pressure used for tires. Pressures are also given in bar.

The big ideas

A rolling tire is constantly being squashed where it meets the road and springing back as it leaves. Rubber is not a perfect spring: each squash-and-recover turns a little energy into heat. That loss, called rolling resistance, is one of the forces the engine or motor must overcome all the time, even on a flat road at a steady speed.

Under-inflated tires squash more, so they waste more energy, wear faster and get hotter. NHTSA says proper inflation can save up to 11 cents per gallon of fuel and extend tire life by 4,700 miles on average, and advises checking all tires, including the spare, at least once a month when cold.

Engineers can design tires with lower rolling resistance using special rubber mixes and shapes. The challenge is to do it without losing grip, especially on wet roads – a tire that saves fuel but cannot stop the car is no good.

Read-through: the teaching steps

  1. Where the energy goes

    Only part of the energy in the fuel actually moves the car. The US Department of Energy says only about 20% of the energy released from gasoline reaches the wheels; the rest is lost in the engine, the drivetrain and accessories. Of the energy that does reach the wheels, some goes into pushing air aside (aerodynamic drag), some into braking, and some into rolling resistance. At town speeds, rolling resistance is one of the biggest of these.

  2. Why a tire loses energy

    Look at the tread and sidewall drawing on the lesson page. Where the tire touches the road, the contact patch is flattened and the sidewall bulges. As the wheel turns, every part of the tire is squashed and released, hundreds of times a minute. The rubber warms up – that heat is the lost energy. This effect is called hysteresis.

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tire size code.
  3. Calculating the force

    Rolling resistance force = coefficient × weight on the tires.

    Weight (in newtons) ≈ mass (kg) × 10 (using g ≈ 10 N/kg).

    For a 1,500 kg car: weight ≈ 15,000 N. With a typical coefficient of 0.01, rolling resistance ≈ 0.01 × 15,000 = 150 N – about the force needed to lift a 15 kg bag.

  4. Pressure and fuel economy

    Low pressure means a bigger bulge and more squashing, so more energy lost. fueleconomy.gov estimates that gas mileage falls by about 0.2% for every 1 psi drop in the average pressure of all four tires, and that keeping tires correctly inflated improves it by 0.6% on average – up to 3% in some cases.

    The right pressure is on the vehicle's Tire and Loading Information label on the driver's door edge or doorjamb, and in the owner's manual – not the maximum pressure molded on the tire.

  5. Wear and safety

    Under-inflated tires wear on their outer edges, run hotter and can fail; over-inflated tires wear in the center and have a smaller contact patch, so less grip. Either way braking and steering suffer. NHTSA says to check pressure when tires are cold – not driven for at least three hours. Checking and adjusting tires on a real car is a job for an adult or a technician.

  6. Low rolling resistance tires

    Tire makers lower rolling resistance with rubber compounds that lose less energy, stiffer construction and careful tread design. Electric cars often use them because every bit of saved energy adds range. The trade-off is that a compound that loses less energy may also grip less, especially in the wet, so designers must balance economy, grip, noise and wear.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Future and environment lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.