Tyres, fuel economy and rolling resistance – Vehicles and Technology motor mechanics lesson
Lesson 48 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Discover why a tyre wastes energy every time it rolls, how much under-inflation costs in fuel, and how engineers balance low rolling resistance against grip.
- Time
- 40 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
This lesson is for curious learners of 14 and over. The maths uses weight = mass × 10 and simple percentages; a calculator is fine. Real tyre checks should be done by an adult. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If correctly inflated tyres save fuel and make cars safer, why do you think so many tyres on the road are under-inflated? How could cars or fuel stations make checking easier?”
- Later: the homework, then the practice test.
Watch out for
- Using the maximum pressure printed on the tyre wall as the pressure to inflate to. That is the most the tyre can safely hold. The correct pressure comes from the car maker, in the handbook or on the label in the door frame.
- Checking pressure straight after a long drive. Warm tyres read higher. Check when the tyres are cold for a true reading.
- Thinking rolling resistance is friction between the tyre and the road. Grip (friction) is what lets the car steer and brake. Rolling resistance comes mainly from the rubber squashing and recovering, which turns energy into heat.
Hands-on: Roll a ball test: on a smooth floor or a long table, build a ramp from a book and a piece of card. Roll a well-pumped football or basketball down it and mark how far it travels. Let a little air out (with an adult) and roll it again from the same point. Which goes further, and why? Squeeze each ball to feel how much it flattens. You can also look – without touching the valve – at the tyre pressure label inside a parked car's door frame with an adult.
What you will learn
- I can explain what rolling resistance is and where the lost energy goes.
- I can calculate a rolling resistance force from a car's weight and a coefficient.
- I can work out the effect of under-inflation on fuel economy using a percentage per psi.
- I can explain why correct tyre pressure matters for economy, wear and safety.
- I can describe the trade-off between low rolling resistance and grip.
Key words
- rolling resistance
- The force that resists a tyre rolling, caused mainly by the rubber squashing and recovering as it turns.
- hysteresis
- Energy lost as heat when a material is squashed and springs back; the main cause of rolling resistance.
- coefficient of rolling resistance
- A number that compares the rolling resistance force with the weight on the tyre. For car tyres it is typically around 0.01.
- contact patch
- The small area of tyre actually touching the road at any moment.
- psi
- Pounds per square inch, a unit of pressure used for tyres. Pressures are also given in bar.
The big ideas
A rolling tyre is constantly being squashed where it meets the road and springing back as it leaves. Rubber is not a perfect spring: each squash-and-recover turns a little energy into heat. That loss, called rolling resistance, is one of the forces the engine or motor must overcome all the time, even on a flat road at a steady speed.
Under-inflated tyres squash more, so they waste more energy, wear faster and get hotter. That is why the Highway Code advises checking tyre pressures weekly, before a journey and when the tyres are cold, and warns that wrong pressures affect braking and steering.
Engineers can design tyres with lower rolling resistance using special rubber mixes and shapes. The challenge is to do it without losing grip, especially on wet roads – a tyre that saves fuel but cannot stop the car is no good.
Read-through: the teaching steps
Where the energy goes
Only part of the energy in the fuel actually moves the car. The US Department of Energy says only about 20% of the energy released from petrol reaches the wheels; the rest is lost in the engine, the drivetrain and accessories. Of the energy that does reach the wheels, some goes into pushing air aside (aerodynamic drag), some into braking, and some into rolling resistance. At town speeds, rolling resistance is one of the biggest of these.
Why a tyre loses energy
Look at the tread and sidewall drawing on the lesson page. Where the tyre touches the road, the contact patch is flattened and the sidewall bulges. As the wheel turns, every part of the tyre is squashed and released, hundreds of times a minute. The rubber warms up – that heat is the lost energy. This effect is called hysteresis.
Reading a tyre size code. Calculating the force
Rolling resistance force = coefficient × weight on the tyres.
Weight (in newtons) ≈ mass (kg) × 10 (using g ≈ 10 N/kg).
For a 1,500 kg car: weight ≈ 15,000 N. With a typical coefficient of 0.01, rolling resistance ≈ 0.01 × 15,000 = 150 N – about the force needed to lift a 15 kg bag.
Pressure and fuel economy
Low pressure means a bigger bulge and more squashing, so more energy lost. The US government's fueleconomy.gov site estimates that fuel economy falls by about 0.2% for every 1 psi drop in the average pressure of all four tyres, and that keeping tyres correctly inflated improves it by 0.6% on average – up to 3% in some cases.
The right pressure is set by the car maker and given in the handbook and usually on a label inside the door frame or fuel filler flap – not the maximum number moulded on the tyre.
Wear and safety
Under-inflated tyres wear on their outer edges, run hotter and can fail; over-inflated tyres wear in the centre and have a smaller contact patch, so less grip. Either way braking and steering suffer. Pressures should be checked with the tyres cold, because warm air reads higher. Checking and adjusting tyres on a real car is a job for an adult or a technician.
Low rolling resistance tyres
Tyre makers lower rolling resistance with rubber compounds that lose less energy, stiffer construction and careful tread design. Electric cars often use them because every bit of saved energy adds range. The trade-off is that a compound that loses less energy may also grip less, especially in the wet, so designers must balance economy, grip, noise and wear.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Future and environment lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy and EPA, fueleconomy.gov – Keeping your vehicle in shape
- US Department of Energy, Alternative Fuels Data Center – Energy losses in light-duty gasoline vehicles
- The Highway Code – Annex 6. Vehicle maintenance, safety and security
- US Department of Energy and EPA, fueleconomy.gov – Where the energy goes: electric cars
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.