▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Bicycle wheels: spokes, rims and truing (theory) – Vehicles and Technology motor mechanics lesson

Lesson 24 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how thin wire spokes under tension hold up a bicycle, what lacing patterns and dish are, and what "truing" a wheel means in theory.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson is theory only – please do not adjust spokes. A wheel that wobbles, rubs or has a broken spoke should go to a qualified bicycle mechanic. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a wheel made of thin wire can be stronger than a wheel made of solid plastic of the same weight?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the hub hangs from the top spokes. Under load the bottom spokes lose tension most; the change in tension of the bottom spokes carries most of the load.
  • Thinking tightening one spoke a lot will fix a wobble. Truing uses small changes to several spokes while keeping tension even; a big change to one spoke makes the wheel weaker and crooked.
  • Thinking a rear wheel's rim sits centered on its hub. On a rear wheel with gears, the rim is dished – centered in the frame, not between the hub flanges.

Hands-on: Make a model wheel: a paper-plate rim and a cardboard-tube hub joined by elastic bands or string pulled tight. Press down on the hub and notice which "spokes" lose tension. Then, with an adult, look closely at a real bicycle wheel (held still) and count the spokes and how many each spoke crosses.

What you will learn

  • I can explain how a tensioned spoked wheel carries a load.
  • I can describe radial and crossed lacing patterns.
  • I can explain why a rear wheel is "dished".
  • I can describe, in theory, how changing spoke tension moves the rim.
  • I can work out spoke angles and wheel circumference.

Key words

spoke
A thin steel wire joining the hub to the rim, held in tension.
nipple
The small threaded nut that joins a spoke to the rim and sets its tension.
tension
A pulling force along the spoke.
lacing pattern
How the spokes are arranged between hub and rim, for example radial or three-cross.
dish
Offsetting the rim toward one hub flange so it sits central in the frame.
true
A wheel that runs straight (no side-to-side wobble) and round (no up-and-down hop).

The big ideas

This is explanation for understanding, not a repair guide.

A spoked bicycle wheel is a marvel of engineering. Its spokes are thin wires that would buckle instantly if you pushed on their ends, yet a wheel weighing under a kilogram can carry a rider many times heavier. The secret is tension: every spoke is pulled tight, and the rim is squeezed into a stiff, pre-stressed ring.

When a rider sits on the bike, the spokes at the bottom of the wheel lose some of their tension while the others barely change. The hub effectively "stands" on the bottom spokes by reducing their pull. Because all the spokes start tight, none of them goes slack in normal riding.

The pattern of the spokes, the balance of their tensions and the shape called dish decide how strong and straight the wheel is. Adjusting spokes – truing – needs the right tool, a stand and training, so it is done by a qualified bicycle mechanic. This lesson explains the ideas only.

Read-through: the teaching steps

  1. Parts of a spoked wheel

    • Hub: the center, with two flanges drilled for spokes, turning on bearings
    • Spokes: steel wires, typically 28 to 36 per wheel
    • Nipples: threaded nuts at the rim that set each spoke's tension
    • Rim: the hoop that carries the tire

    The bicycle drawing on the lesson page shows the wheels in place.

    SaddleHandlebarsFramePedal and crankChainRear wheel and tireFront wheelBrake
    The main parts of a bicycle.
  2. Tension is the secret

    Each spoke is pre-tensioned. Under load, the spokes nearest the ground lose some tension; that change is what carries the weight. Think of a bicycle wheel as a stiff rim held in balance by many tight wires pulling in every direction. If tension is too low, spokes go slack under load and can loosen or break.

  3. Lacing patterns

    • Radial: spokes run straight out from hub to rim – light and neat, used on some front wheels
    • Crossed (2-cross, 3-cross): spokes leave the hub at an angle and cross others on the way – they can carry twisting forces from pedaling and hub brakes

    Rear wheels and disc-brake wheels need crossed spokes because torque must pass from the hub to the rim.

  4. Dish

    On a rear wheel with gears, the cassette takes up space on one side, so the hub flanges are not equally spaced from the center. To put the rim in the middle of the frame, the spokes on the gear side are tighter than those on the other side. This offset is called dish.

  5. Truing in theory

    A wheel can be out of true sideways (a wobble) or up and down (a hop). In principle, tightening a spoke pulls the rim toward the hub flange it comes from; loosening it lets the rim move away. A mechanic makes small changes to several spokes in a wheel stand, keeping the overall tension even. Doing it wrong can make a wheel weak or crooked, so it is left to trained people.

  6. Wheel math

    • Angle between spokes on one wheel: 360° ÷ number of spokes
    • Spokes per side: total ÷ 2
    • Circumference = π × diameter

    A wheel 0.68 m across has a circumference of about π × 0.68 ≈ 2.14 m.

  7. Safety and reflectors

    A broken or loose spoke, a dented rim or a wobble that rubs the brakes is a reason to stop riding until a qualified bicycle mechanic has checked the wheel. Keep fingers away from spokes when a wheel is turning. In the US, the CPSC requirements call for wheel (spoke) reflectors or reflective rims or tire sidewalls on new bicycles.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.