▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Bicycle tires, tubes and punctures – Vehicles and Technology motor mechanics lesson

Lesson 25 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how bicycle tires and inner tubes hold air, what the sidewall markings mean, and why punctures and pinch flats happen.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson is look-only. If you pump up a bicycle tire together, stay within the range printed on the sidewall. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Tubeless tires seal small holes themselves. Do you think inner tubes will disappear? Why or why not?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking more pressure is always faster and better. Above the right pressure the tire bounces off bumps and grips less; and pumping beyond the sidewall maximum risks a burst.
  • Thinking a pinch flat is caused by something sharp. A pinch flat is caused by the rim squashing the tube in a hard hit; it leaves two slits side by side.
  • Thinking all valves are the same. Presta and Schrader valves differ in size and how they open; a pump head must match.

Hands-on: With an adult, look at a bicycle tire sidewall and find the ISO size, the pressure range and the valve type. Write them down and convert the pressure range between psi and bar. Do not pump the tire or take it off. Squeeze a balloon gently to feel how pressure makes something firm.

What you will learn

  • I can compare tires with inner tubes, tubeless tires and tubulars.
  • I can tell Presta and Schrader valves apart.
  • I can read an ISO (ETRTO) tire size such as 37-622.
  • I can explain the causes of punctures and pinch flats.
  • I can convert tire pressures between psi and bar.

Key words

clincher
A tire whose beads hook into the rim, usually with an inner tube inside.
inner tube
A rubber ring of air inside a tire.
tubeless
A tire that seals to the rim without a tube, often with liquid sealant inside.
Presta valve
A slim valve with a small locknut at the tip, common on road bikes.
Schrader valve
A wider valve like the one on a car tire.
pinch flat
A puncture made when the tube is squashed against the rim by a hard hit, leaving two small slits.

The big ideas

A bicycle tire is a flexible casing of fabric and rubber. On most bikes, an inner tube inside the tire holds the air, and the tire's beads hook under the edges of the rim. The air pressure makes the tire firm enough to roll easily and carry the rider, while still soaking up small bumps.

Pressure is a balance. Too little and the tire squirms, wears quickly and is easily pinched against the rim. Too much and it bounces, grips less and gives a harsh ride. In the US, the CPSC bicycle requirements say the recommended pressure must be molded on the tire sidewall – unlike cars, where the vehicle maker's label gives it.

This lesson explains how tires work and why they go flat. Fitting tires and pumping them up are practical jobs for an adult who knows how or a qualified bicycle mechanic; never pump a tire beyond the range on its sidewall, because an over-inflated tire can burst with a loud bang.

Read-through: the teaching steps

  1. Three kinds of tire

    • Clincher with inner tube: the most common; the tube holds the air
    • Tubeless: the tire seals directly to a special rim, often with liquid sealant that plugs small holes
    • Tubular: the tube is sewn inside the tire, which is glued to the rim – mostly used in racing
    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tire size code.
  2. Valves

    • Schrader: wide, with a spring-loaded pin in the middle – the same type as on car tires
    • Presta: slim, with a small locknut at the tip that is undone before air can pass – common on road bikes because it needs only a small hole in a narrow rim

    Pumps often have a head that fits both.

  3. Reading the size

    Many tires show an ISO (ETRTO) size such as 37-622: the tire is about 37 mm wide and fits a rim with a 622 mm bead-seat diameter. The same tire may also show a traditional size such as 700 × 35C or 28 × 1.40. The ISO number is the reliable one for matching tire and rim.

  4. Pressure units

    Pressure is usually shown in psi (pounds per square inch), and also in bar.

    1 bar ≈ 14.5 psi

    A tire marked 58–87 psi is about 4–6 bar. The sidewall gives the range; the right figure within it depends on the rider's weight and the riding.

  5. Why tires go flat

    • Puncture: something sharp – glass, a thorn, a flint – goes through the tread and the tube
    • Pinch flat: hitting a curb or pothole squashes the tube against the rim edge, making two small slits side by side (a "snakebite")
    • Slow leaks: a worn valve, or air slowly passing through the rubber over weeks

    Keeping the pressure within the sidewall range is the best defense against pinch flats.

  6. How a patch works (theory)

    A puncture patch is a piece of thin rubber that bonds over the hole, sealing it so the tube holds air again. The bond only works on a clean, dry surface. Sealant in tubeless tires works differently: liquid is pushed into the hole by escaping air and sets there. Repairs are done by an adult who knows how or a bicycle mechanic.

  7. Safety

    Check tires by looking: cuts, bulges, worn-through tread or threads showing are reasons to stop riding and ask an adult. Over-inflated tires can burst loudly and injure, so pumping is done by an adult, never beyond the sidewall range.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.