▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Bicycle brakes: rim, disc and coaster – Vehicles and Technology motor mechanics lesson

Lesson 23 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Compare rim, disc and coaster brakes on bicycles, find out how levers and hydraulics multiply a squeeze, and use a real US stopping-distance standard in the math.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

Please do not adjust brakes as part of this lesson. If a bicycle's brakes seem weak or noisy, take it to a qualified bicycle mechanic. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Should all children's bicycles have hand brakes, coaster brakes or both? Explain your choice.”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking using the front brake will always throw you over the handlebars. Smooth, progressive use of the front brake gives the most stopping power; it is grabbing it hard and suddenly that is dangerous.
  • Thinking rim brakes work equally well in the rain. Water on the rim reduces friction until it is wiped off, so wet braking takes longer.
  • Thinking a coaster brake works on both wheels. A coaster brake is in the rear hub and only slows the rear wheel.

Hands-on: With an adult, look at the brakes on two different bicycles and decide whether each is a rim, disc or coaster brake. Watch (do not touch) as the adult squeezes a lever: which parts move? Then make a card lever with a split-pin pivot and measure how far each end moves, to see the mechanical advantage.

What you will learn

  • I can describe how rim, disc and coaster brakes work.
  • I can explain why rim brakes are weaker in the wet.
  • I can calculate the mechanical advantage of a brake lever.
  • I can explain why the front brake does most of the stopping.
  • I can describe the US stopping standard for bicycles sold there.

Key words

rim brake
A brake whose pads squeeze the wheel rim.
disc brake
A brake whose pads squeeze a disc (rotor) fixed to the hub.
coaster brake
A brake inside the rear hub, worked by pedaling backward.
V-brake
A rim brake with two long arms pulled together by a cable.
mechanical advantage
How many times a lever or system multiplies the input force.
modulation
How finely a rider can control the amount of braking.

The big ideas

All bicycle brakes do the same job: they press a friction material against something that turns with the wheel, turning the bicycle's movement energy into heat. Where they press is what makes the difference.

Rim brakes squeeze the rim of the wheel. They are light and simple, but a wet or muddy rim makes them weaker, and they slowly wear the rim. Disc brakes squeeze a separate disc at the hub, away from water and mud, and give strong, consistent braking; they may be cable-operated or hydraulic. Coaster brakes are hidden inside the rear hub and work when the rider pedals backward; they are common on children's bikes and town bikes.

In the US, the Consumer Product Safety Commission sets a stopping standard for bicycles sold there. This lesson explains how brakes work; adjusting or repairing brakes is a job for a qualified bicycle mechanic or an adult who knows how, not something to try from a lesson.

Read-through: the teaching steps

  1. Rim brakes

    Rim brakes come in several shapes:

    • Caliper (side-pull or dual-pivot): a horseshoe-shaped clamp over the tire, common on road bikes
    • V-brake: two long arms, giving a lot of leverage, common on hybrid and children's bikes
    • Cantilever: arms pivoting on studs, used on older mountain and touring bikes

    Pads squeeze the rim's braking surface. Water on the rim acts like a lubricant until it is wiped away, so wet braking takes longer.

  2. Disc brakes

    A disc (rotor) is bolted to the hub and a caliper on the frame or fork holds the pads. Mechanical discs are pulled by a cable; hydraulic discs use fluid, like a car. Because the disc is near the hub, it stays cleaner and drier, so braking is more consistent. The disc-brake drawing on the lesson page shows the layout.

    CaliperBrake discFluidPistonPadsDisc (edge on)
    A disc brake: fluid pressure pushes the piston, the pads squeeze the spinning disc, and friction turns movement into heat.
  3. Coaster brakes

    A coaster brake sits inside the rear hub. Pedaling forward drives the wheel; pedaling backward pushes a brake shoe or cone outwards against the inside of the hub. It needs no lever or cable, but it works only on the rear wheel and cannot be used if the chain comes off.

  4. Levers multiply force

    A brake lever is a lever: the rider squeezes near the end, and the cable is pulled near the pivot. If the hand is 80 mm from the pivot and the cable 20 mm, the mechanical advantage is 80 ÷ 20 = 4. The brake arms multiply the force again. Hydraulic brakes add a further multiplication through piston areas.

  5. Front and rear

    When a bicycle slows, weight shifts forward. The front tire is pressed down harder and can take more braking force, so the front brake can do most of the stopping. Braking with the rear alone takes longer because the light rear wheel locks and skids more easily. Riders learn to use both brakes smoothly.

    SaddleHandlebarsFramePedal and crankChainRear wheel and tireFront wheelBrake
    The main parts of a bicycle.
  6. The US stopping standard

    The CPSC bicycle requirements (16 CFR 1512) say a bicycle with hand brakes must stop within 15 feet from 15 mph with a 150-pound rider, and a bicycle with only a foot (coaster) brake within 15 feet from 10 mph. Rules in other countries differ.

  7. Safety

    Brakes are safety-critical. If brakes feel weak, rub or make a strange noise, an adult takes the bicycle to a qualified bicycle mechanic. When you look at brakes, an adult is with you, the bicycle is held steady and you keep fingers away from discs and spokes – a disc can be hot and sharp-edged after a ride.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.