▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Bicycle tyres, tubes and punctures – Vehicles and Technology motor mechanics lesson

Lesson 25 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how bicycle tyres and inner tubes hold air, what the sidewall markings mean, and why punctures and pinch flats happen.

Time
40 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

How to use this lesson

This lesson is look-only. If you pump up a bicycle tyre together, stay within the range printed on the sidewall. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Tubeless tyres seal small holes themselves. Do you think inner tubes will disappear? Why or why not?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking more pressure is always faster and better. Above the right pressure the tyre bounces off bumps and grips less; and pumping beyond the sidewall maximum risks a burst.
  • Thinking a pinch flat is caused by something sharp. A pinch flat is caused by the rim squashing the tube in a hard hit; it leaves two slits side by side.
  • Thinking all valves are the same. Presta and Schrader valves differ in size and how they open; a pump head must match.

Hands-on: With an adult, look at a bicycle tyre sidewall and find the ISO size, the pressure range and the valve type. Write them down and convert the pressure range between bar and psi. Do not pump the tyre or take it off. Squeeze a balloon gently to feel how pressure makes something firm.

What you will learn

  • I can compare tyres with inner tubes, tubeless tyres and tubulars.
  • I can tell Presta and Schrader valves apart.
  • I can read an ISO (ETRTO) tyre size such as 37-622.
  • I can explain the causes of punctures and pinch flats.
  • I can convert tyre pressures between bar and psi.

Key words

clincher
A tyre whose beads hook into the rim, usually with an inner tube inside.
inner tube
A rubber ring of air inside a tyre.
tubeless
A tyre that seals to the rim without a tube, often with liquid sealant inside.
Presta valve
A slim valve with a small locknut at the tip, common on road bikes.
Schrader valve
A wider valve like the one on a car tyre.
pinch flat
A puncture made when the tube is squashed against the rim by a hard hit, leaving two small slits.

The big ideas

A bicycle tyre is a flexible casing of fabric and rubber. On most bikes, an inner tube inside the tyre holds the air, and the tyre's beads hook under the edges of the rim. The air pressure makes the tyre firm enough to roll easily and carry the rider, while still soaking up small bumps.

Pressure is a balance. Too little and the tyre squirms, wears quickly and is easily pinched against the rim. Too much and it bounces, grips less and gives a harsh ride. In the US, the CPSC bicycle requirements say the recommended pressure must be moulded on the tyre sidewall – unlike cars, where the vehicle maker's label gives it.

This lesson explains how tyres work and why they go flat. Fitting tyres and pumping them up are practical jobs for an adult who knows how or a qualified bicycle mechanic; never pump a tyre beyond the range on its sidewall, because an over-inflated tyre can burst with a loud bang.

Read-through: the teaching steps

  1. Three kinds of tyre

    • Clincher with inner tube: the most common; the tube holds the air
    • Tubeless: the tyre seals directly to a special rim, often with liquid sealant that plugs small holes
    • Tubular: the tube is sewn inside the tyre, which is glued to the rim – mostly used in racing
    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tyre size code.
  2. Valves

    • Schrader: wide, with a spring-loaded pin in the middle – the same type as on car tyres
    • Presta: slim, with a small locknut at the tip that is undone before air can pass – common on road bikes because it needs only a small hole in a narrow rim

    Pumps often have a head that fits both.

  3. Reading the size

    Many tyres show an ISO (ETRTO) size such as 37-622: the tyre is about 37 mm wide and fits a rim with a 622 mm bead-seat diameter. The same tyre may also show a traditional size such as 700 × 35C or 28 × 1.40. The ISO number is the reliable one for matching tyre and rim.

  4. Pressure units

    Pressure may be shown in bar and in psi (pounds per square inch).

    1 bar ≈ 14.5 psi

    A tyre marked 4–6 bar is about 58–87 psi. The sidewall gives the range; the right figure within it depends on the rider's weight and the riding.

  5. Why tyres go flat

    • Puncture: something sharp – glass, a thorn, a flint – goes through the tread and the tube
    • Pinch flat: hitting a kerb or pothole squashes the tube against the rim edge, making two small slits side by side (a "snakebite")
    • Slow leaks: a worn valve, or air slowly passing through the rubber over weeks

    Keeping the pressure within the sidewall range is the best defence against pinch flats.

  6. How a patch works (theory)

    A puncture patch is a piece of thin rubber that bonds over the hole, sealing it so the tube holds air again. The bond only works on a clean, dry surface. Sealant in tubeless tyres works differently: liquid is pushed into the hole by escaping air and sets there. Repairs are done by an adult who knows how or a bicycle mechanic.

  7. Safety

    Check tyres by looking: cuts, bulges, worn-through tread or threads showing are reasons to stop riding and ask an adult. Over-inflated tyres can burst loudly and injure, so pumping is done by an adult, never beyond the sidewall range.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Bicycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.