▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Wheels: rims, offset, fixings and bearings – Motor Vehicle Theory motor mechanics lesson

Lesson 88 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Learn the parts of a wheel rim, what offset and pitch circle diameter mean, why wheel nuts and bolts must match the wheel, and how a wheel bearing lets the wheel spin freely.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

The calculations use half-widths, subtraction and the sine rule for a regular polygon. Fitting wheels involves lifting a vehicle and tightening fixings to the maker's torque, so it is for trained technicians only. Values are dated; check the official source before relying on them. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Many people fit wider wheels to make a car look sportier. What questions should they ask before changing wheels, and who should they ask?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking any nut that fits the thread will do. The seat shape must match the wheel. A tapered nut on a wheel made for ball-seat nuts, for example, has only a tiny contact area and can work loose.
  • Thinking offset is the same as the rim width. Offset is where the mounting face sits relative to the middle of the rim. Two wheels of the same width can sit in quite different places.
  • Thinking a noisy wheel bearing is just a nuisance. A worn bearing can develop play and, in the worst case, break up. The noise is a warning to have it checked.

Hands-on: Draw a cross-section of a wheel rim to scale on squared paper: a 7-inch width (177.8 mm, drawn at half size), the center line, and a mounting face 45 mm toward the outside. Label the flanges, bead seats, safety humps and well. Then redraw it as 8J with a 40 mm offset and measure how the edges move. If you look at a real wheel, do it with a qualified adult on a parked, switched-off car, without touching the nuts or bolts.

What you will learn

  • I can name the parts of a wheel rim and explain the jobs of the well and the safety humps.
  • I can explain rim width, offset, pitch circle diameter and center bore.
  • I can work out how a change of wheel width and offset moves the tire in or out.
  • I can explain why wheel fixings must match the wheel and are tightened to the manufacturer's figure.
  • I can describe the types of wheel bearing and the signs that one is worn.

Key words

offset
The distance from the center line of the rim to the face that bolts onto the hub. Often marked ET, in millimeters. Positive offset puts the mounting face toward the outside of the wheel.
pitch circle diameter (PCD)
The diameter of the circle through the centers of the wheel studs or bolts, for example 5 × 114.3 mm.
well
The deep, narrow center of the rim. It lets the tire bead drop in so the tire can be fitted over the flange.
hub-centric
A wheel that is centered on the hub by a close-fitting center bore, rather than by the nuts or bolts alone.
wheel bearing
The bearing in the hub that carries the weight of the car and lets the wheel turn with little friction.

The big ideas

A road wheel looks simple, but it must carry part of the car's weight, the twisting forces of braking and driving, and the sideways forces of cornering, while spinning hundreds of times a minute. It must also hold the tire's beads tightly, fit the hub exactly and sit in the right place inside the wheel well.

The main measurements of a wheel are its diameter and width, its offset – how far the mounting face is from the middle of the rim – and its fixing pattern: the number of studs or bolts and the pitch circle diameter. Change any of them and the tire may rub, the steering may feel different, or the wheel may not be held securely.

Behind the wheel, the wheel bearing lets it spin freely. This lesson explains how wheels, fixings and bearings work. Removing and refitting wheels involves lifting the vehicle and tightening fixings to the manufacturer's figures, so it is work for a trained technician; never go under a vehicle supported only by a jack.

Read-through: the teaching steps

  1. Steel and alloy wheels

    Steel wheels are pressed from sheet steel and welded together. They are strong, cheap and bend rather than crack, so they suit vans and winter use.

    Alloy wheels are cast or forged from aluminum alloy. They are lighter, which reduces unsprung mass, can be shaped to cool the brakes, and look smart, but they cost more and can crack if hit hard.

  2. The parts of a rim

    • Flanges – the raised edges that hold the tire sideways.
    • Bead seats – where the tire beads sit and seal.
    • Safety humps – small ridges just inside the bead seats that help keep a deflated tire's beads in place.
    • Well – the deep center that lets the bead drop in so the tire can be fitted.

    A rim size such as 7J × 16 means a rim 7 inches wide between the flanges, a J flange profile, and a 16-inch diameter.

  3. Offset

    Offset (ET) is the distance from the rim's center line to the mounting face. With a positive offset, the mounting face is toward the outside of the wheel, so the wheel tucks in under the car – common on front-wheel-drive cars.

    Lowering the offset pushes the wheel out; raising it pulls the wheel in. Because offset and width both matter:

    • outer edge position = half the width − offset (measured outwards from the hub face)
    • inner edge position = half the width + offset (measured inwards from the hub face)

    The wrong offset can make the tire rub, overload the wheel bearing and change the scrub radius, which affects steering feel.

  4. Fixings: studs, nuts and bolts

    Wheels are fixed by nuts on studs or by bolts screwed into the hub. Their number and the pitch circle diameter must match the hub: a 5 × 114.3 wheel has five fixings on a 114.3 mm circle.

    The seat of each nut or bolt – tapered, ball-shaped or flat – must match the shape in the wheel, or it can work loose. Many wheels are hub-centric: a close-fitting center bore centers the wheel, and the fixings clamp it. Fixings are tightened in a set pattern to the vehicle maker's torque figure, and are often checked again after a short distance.

  5. Wheel bearings

    Older cars often used a pair of tapered roller bearings in each hub, which were greased and adjusted. Most modern cars use a sealed hub bearing unit – usually a double row of balls in one sealed assembly – that is never adjusted and is replaced as a unit when worn. Many carry a magnetic ring read by the anti-lock brake wheel speed sensor.

    A worn bearing usually makes a rumble or drone that rises with road speed and changes when cornering, and in time it develops play.

  6. Wheels in a state inspection

    Where a state requires a periodic safety inspection, tires, wheels and rims are one of the steps checked – in Virginia, for example. Rules are set by each state, so check your own state's official source.

    In a workshop, a technician checks for loose or missing lug nuts, cracked or bent wheels, mismatched fixings and bearing play or noise, and compares findings with the manufacturer's data.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Wheels and tires lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.