▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Wheel balancing and tire wear diagnosis – Motor Vehicle Theory motor mechanics lesson

Lesson 89 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Discover why a few grams out of balance can shake a steering wheel, how a balancing machine finds the heavy spot, and how to read a tire's wear pattern like a detective.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

The force calculation uses F = m r ω². The bicycle activity needs an adult to hold the bicycle steady. Balancing and fitting tires is for trained fitters. Values are dated; check the official source before relying on them. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “A tire with plenty of tread but a strange wear pattern may be legal, yet a fitter might still be worried. Why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking new tires do not need balancing. No tire and wheel is perfectly even. New tires are always balanced when fitted.
  • Thinking a vibration that only appears at speed is not important. Out-of-balance force grows with the square of speed, wearing tires, bearings and suspension. It should be checked.
  • Replacing worn tires without asking why they wore. Uneven wear has a cause. If it is not found, the new tires will wear the same way.

Hands-on: Tape a coin near the rim of a bicycle wheel, with an adult holding the bicycle upside down and steady. Let the wheel turn freely and watch it settle with the coin at the bottom: that is static imbalance. Spin it gently and feel the frame shake. Then tape a second coin opposite the first and try again. Keep fingers well clear of the spokes and brakes.

What you will learn

  • I can explain static and dynamic imbalance and the vibration each causes.
  • I can describe how a balancing machine shows where weights are needed.
  • I can calculate the force from an out-of-balance mass and explain why it grows quickly with speed.
  • I can link tire wear patterns to their likely causes.
  • I can state NHTSA's tread replacement point and its advice on rotation.

Key words

static imbalance
A heavy spot on the wheel and tire that makes it hop up and down as it turns. A wheel with static imbalance, free to turn, settles with the heavy spot at the bottom.
dynamic imbalance
Uneven mass across the width of the wheel that makes it wobble from side to side as it turns.
balance weight
A small weight clipped or stuck to the rim to cancel a heavy spot.
feathering
Tread blocks worn sharp on one side and rounded on the other, usually caused by wrong toe.
cupping
Scooped-out patches spaced round the tread, usually caused by worn shock absorbers or an out-of-balance wheel.

The big ideas

No tire and wheel is made perfectly even. A few grams more on one side than the other may not sound like much, but at highway speed the wheel spins more than ten times a second, and that small mass is flung outwards with a force many times its weight. The result is a vibration in the steering wheel or the seat, extra wear on the tires and suspension, and a tiring drive.

Balancing fixes this. A machine spins the wheel and tire, measures the vibration, and shows where small weights should be fixed to the rim to cancel the heavy spots.

Tires also keep a record of how they have been treated. The way the tread has worn – in the center, on the shoulders, on one edge, in patches – points to under-inflation, over-inflation, alignment faults or worn suspension. This lesson explains balancing and how to read the clues. Balancing, fitting and inflating tires is work for a trained fitter.

Read-through: the teaching steps

  1. Static imbalance

    If a wheel and tire has a heavy spot, the wheel, free to turn on a horizontal axle, will roll until the heavy spot is at the bottom. That is static imbalance.

    As the wheel turns, the heavy spot is flung outwards, lifting the wheel at the top of each turn and pushing it down at the bottom. The wheel hops, and the driver feels a vibration at a particular speed.

  2. Dynamic imbalance

    A wheel can be balanced statically but still have uneven mass across its width – heavy on the inner edge at one point and on the outer edge at the opposite point. As it spins, these try to twist the wheel, making it wobble from side to side.

    On a front wheel this is felt as shimmy in the steering wheel. Modern balancing machines correct both kinds at once, with weights on the inner and outer edges of the rim.

  3. The balancing machine

    A fitter mounts the wheel and tire on the machine's shaft and enters the rim size. The machine spins it, and sensors measure the forces. It then shows how many grams are needed on each edge of the rim and where.

    Weights may be clipped onto the rim flange or stuck inside the rim (often on alloy wheels). The wheel is spun again to check. Some machines also press a roller against the tire to find stiff spots in the tire itself, called road force variation.

  4. Why speed makes it worse

    The outward force from an out-of-balance mass is:

    F = m × r × ω²

    where m is the mass in kg, r its distance from the center in meters, and ω the angular speed in radians per second (ω = 2π × revolutions per second). Because speed is squared, doubling the speed makes the force four times as large. That is why a wheel can feel smooth in town but shake on a fast road.

  5. Reading tire wear

    • Both shoulders worn – under-inflation.
    • Center worn – over-inflation.
    • One shoulder worn – camber, often from a knock or worn parts.
    • Feathered tread – wrong toe.
    • Cupped patches round the tire – worn shock absorbers or an out-of-balance wheel.
    • A flat spot – a skid with a locked wheel.

    A technician uses these clues to find and fix the cause, not just replace the tire.

  6. Tread depth and checks in the US

    NHTSA says tires should be replaced when the tread is worn down to 2/32 of an inch, and describes the penny test: with Lincoln's head upside down in the groove, if you can see the top of his head, replace the tire. NHTSA also says to check pressures at least once a month when cold, and, if the vehicle maker recommends rotating the tires, to do it every 5,000 to 8,000 miles. Rotation helps even out wear between positions.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Wheels and tires lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.