▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Electrical principles: voltage, current, resistance and power – Motor Vehicle Theory motor mechanics lesson

Lesson 90 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out what voltage, current, resistance and power really mean in a car's electrical system, and use Ohm's law and the power formula to work out what a circuit is doing.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This level 3 lesson uses Ohm's law and the power formula, so a calculator helps. It explains how vehicle electrics work; any practical work on a real vehicle belongs in a college workshop with a qualified teacher. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think designers are moving some vehicle systems to higher voltages, and what new safety problems does that create for the people who repair them?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking current is "used up" as it goes round a circuit. The same current flows all the way round a simple loop. It is energy that is turned into heat and light in the load, not current.
  • Thinking that because 12 V cannot shock you, a car battery is harmless. The danger is the very high current it can deliver into a short circuit, plus its gases and acid. Burns and fires come from current, not just voltage.
  • Mixing up the formulas, for example working out I = R ÷ V. Write V = I × R first and rearrange. Check units: volts ÷ ohms gives amps.

Hands-on: Find the rating label on three household appliances (a kettle, a phone charger and a lamp, for example) without opening or plugging anything in. Write down the voltage and the power on each, then use I = P ÷ V to work out the current each one draws. Then imagine the same power at 12 V and work out the current again. Which would need the thickest cable? Do not open any appliance or touch any vehicle battery or wiring.

What you will learn

  • I can define voltage, current, resistance and power and give the unit and symbol of each.
  • I can use Ohm's law (V = I × R) to find any one value from the other two.
  • I can use P = V × I to find the power of a vehicle load or the current it draws.
  • I can explain why a low-voltage system can still be dangerous and why high-voltage systems are for trained technicians only.

Key words

voltage (V)
The electrical "push" (potential difference) between two points, measured in volts. A car's low-voltage system is nominally 12 volts.
current (I)
The rate at which electric charge flows round a circuit, measured in amperes (amps, A).
resistance (R)
How much a component opposes the flow of current, measured in ohms (Ω).
power (P)
The rate at which electrical energy is turned into heat, light or movement, measured in watts (W). P = V × I.
Ohm's law
For a resistor at a steady temperature, V = I × R: the current is proportional to the voltage.

The big ideas

Almost every system on a modern vehicle depends on electricity: starting, charging, lighting, the fuel injectors and the electronic control module that runs the engine. The US Department of Energy's guide to how gasoline cars work lists the battery, which starts the engine and powers the electronics, and the electronic control module, which controls the fuel mixture and ignition timing, among the main parts of the car. To understand any of them you need four quantities: voltage, current, resistance and power.

A helpful picture is water in a pipe. Voltage is like the pressure that pushes the water, current is like the rate at which it flows, and resistance is like a narrow section of pipe that restricts the flow. Power is how quickly the energy is being used. The picture is not perfect, but it explains why a higher voltage or a lower resistance makes more current flow.

Two formulas do most of the work: Ohm's law, V = I × R, and the power formula, P = V × I. With them a technician can predict the current a bulb should draw, the size of fuse it needs, or why a corroded connection makes a lamp dim. This lesson explains the ideas; it is not a guide to working on a vehicle's wiring.

Read-through: the teaching steps

  1. Voltage: the push

    Voltage is the difference in electrical "pressure" between two points. It is measured in volts (V) with a voltmeter connected across the two points.

    • A typical car or motorcycle low-voltage system is nominally 12 V; many trucks use 24 V.
    • A fully charged 12 V lead-acid battery typically reads a little above 12 V when resting, and the charging system typically holds the system at about 14 V when the engine runs.
    • Electric and hybrid vehicles also carry a high-voltage system. HSE says these currently run at up to 650 V DC. That system is for trained technicians only.
    +12 VBatteryFuseSwitchLampReturn through the body (ground)
    A simple lighting circuit. On a car the metal body is the return path (ground).
  2. Current: the flow

    Current is the rate of flow of electric charge, measured in amperes (A) with an ammeter placed in the circuit, so that all the current passes through it.

    Current only flows when there is a complete loop: from the battery, through the switch and the load, and back to the battery. Conventional current is drawn flowing from positive to negative. (The electrons themselves move the other way, but every wiring diagram uses conventional current.)

    Typical loads range from a fraction of an amp for a small LED lamp to well over 100 A for a starter motor.

  3. Resistance: the opposition

    Resistance is how strongly a component opposes current, measured in ohms (Ω).

    • A wire has a small resistance, which goes up if it is longer, thinner or hotter.
    • A bulb filament has a much higher resistance, so it gets hot and glows.
    • A dirty or corroded connection adds unwanted resistance.

    Resistance turns electrical energy into heat. That is useful in a heater element and harmful in a bad joint, which can get hot enough to melt insulation.

  4. Ohm's law

    For a resistor at a steady temperature the current is proportional to the voltage:

    • V = I × R
    • I = V ÷ R
    • R = V ÷ I

    A quick way to remember it is a triangle with V at the top and I and R side by side at the bottom: cover the one you want and the other two show how to find it.

    Example: a 12 V supply across a 4 Ω heater element gives I = 12 ÷ 4 = 3 A. Halve the resistance and the current doubles.

  5. Power: how fast energy is used

    Electrical power is P = V × I, measured in watts (W). Rearranged, I = P ÷ V. Two more forms come from combining it with Ohm's law: P = I² × R and P = V² ÷ R.

    This is how a technician estimates current: a 60 W headlamp bulb on a 12 V system draws about 60 ÷ 12 = 5 A. Energy used is power × time, so a 5 W load left on for 10 hours uses 50 watt-hours. That is why a light left on overnight can flatten a battery.

  6. Why 12 volts still needs respect

    12 V is too low to give most people a shock through dry skin, but a vehicle battery can deliver hundreds of amps. A metal tool or a ring across its terminals can glow red hot in seconds and cause burns, and battery gases and acid are further hazards. Electric and hybrid vehicles also carry a high-voltage system, often several hundred volts DC, with the high-voltage cables usually colored orange. Look, never touch: work on any vehicle electrical system is done by, or with, a qualified technician.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.