▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Valve trains: OHC, DOHC and pushrod – Motor Vehicle Theory motor mechanics lesson

Lesson 24 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Compare overhead cam, double overhead cam and pushrod valve trains, and learn how cams, followers and springs open and close the valves at the right time.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains valve trains for understanding. The activity is a card model. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think most modern car engines use overhead camshafts rather than pushrods?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the camshaft turns at crankshaft speed. In a four-stroke engine it turns at half crankshaft speed.
  • Thinking valve clearance should be zero on every engine. Mechanical systems need a small clearance for expansion; hydraulic lifters take it up automatically.
  • Thinking DOHC means two valves per cylinder. DOHC means two camshafts per head; many DOHC engines have four valves per cylinder.

Hands-on: Make a cam from stiff card: cut a circle with a raised 'nose', push a pencil through the center as the shaft, and rest a card strip 'follower' on top inside a box slot. Turn the pencil and watch the follower rise and fall. Measure the base circle radius and the nose radius and work out the lift.

What you will learn

  • I can describe how a camshaft opens and springs close the valves.
  • I can compare OHV (pushrod), SOHC and DOHC layouts.
  • I can explain why the camshaft turns at half crankshaft speed.
  • I can explain valve clearance and hydraulic lifters.
  • I can calculate valve lift from cam lift and rocker ratio.

Key words

camshaft
A shaft with lobes (cams) that open the valves in time with the crankshaft.
OHV / pushrod
Overhead valve layout with the camshaft in the block, using pushrods and rockers.
OHC / DOHC
Overhead camshaft: one (SOHC) or two (DOHC) camshafts in each head.
valve clearance (lash)
A small gap in the valve train when the valve is closed, allowing for expansion.
rocker ratio
How much a rocker arm multiplies the cam's lift at the valve.

The big ideas

A four-stroke engine breathes through valves: inlet valves let the air–fuel mixture in, exhaust valves let burned gas out. They must open and close at exactly the right moments, thousands of times a minute. The valve train does this: a camshaft with egg-shaped lobes pushes each valve open, and a spring snaps it shut.

There are three main layouts. Pushrod engines keep the camshaft in the block; overhead cam engines put it in the cylinder head; double overhead cam engines use two camshafts per head. This lesson compares them, explains valve clearance and teaches the sums for camshaft speed and valve lift.

It is theory for understanding; engine work is done by trained technicians.

Read-through: the teaching steps

  1. Cams and valves

    A cam lobe is round (the base circle) with a raised nose. As it turns, the nose pushes a follower, which opens the valve. When the nose has passed, the valve spring closes the valve onto its seat.

    Cam lift = maximum radius of the lobe − base circle radius. See the valves above the cylinder in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. Half-speed camshaft

    Each valve opens once per four-stroke cycle. The cycle takes two crankshaft revolutions, so the camshaft turns once for every two crankshaft turns:

    camshaft speed = crankshaft speed ÷ 2.

    The timing belt, chain or gears drive the camshaft at this 2:1 ratio.

  3. Pushrod (OHV) engines

    The camshaft is in the block, near the crankshaft. Lifters ride on the cams, pushrods carry the motion up, and rocker arms pivot to push the valves down. Simple and compact – especially in V engines, where one camshaft serves both banks – but the many moving parts limit high-rpm running.

  4. Overhead cam engines

    • SOHC – one camshaft per head, often with rockers to work both inlet and exhaust valves.
    • DOHC – two camshafts per head, one for inlet and one for exhaust, usually acting directly on bucket followers.

    Fewer moving parts between cam and valve allow higher rpm, and DOHC makes four valves per cylinder easy to arrange.

  5. Rocker ratio

    A rocker arm is a lever. If the valve side is longer than the cam side, the valve moves further than the cam lifts:

    valve lift = cam lift × rocker ratio.

    A ratio of 1.5:1 turns 6 mm of cam lift into 9 mm of valve lift.

  6. Valve clearance and hydraulic lifters

    Valve train parts expand when hot. A small clearance (lash) when cold makes sure the valve still closes fully when hot. Too little clearance can hold a valve open and burn it; too much makes noise and reduces lift. Many engines use hydraulic lifters, which use oil pressure to take up the clearance automatically. Where clearances are adjustable, the manufacturer's data gives the values.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.