▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Valve timing, overlap and variable valve timing – Motor Vehicle Theory motor mechanics lesson

Lesson 25 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Learn why valves open before and close after the dead centers, how to calculate valve duration and overlap, and how variable valve timing helps an engine at all speeds.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains valve timing using example angles. The activity is a timing diagram on paper. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think valve timing that suits a racing engine would make a family car difficult to drive in town?”
  4. Later: the homework, then the practice test.

Watch out for

  • Forgetting the 180° when calculating duration. Duration includes the whole stroke between the dead centers plus the early and late angles.
  • Subtracting the overlap angles. Inlet opening before TDC and exhaust closing after TDC are on opposite sides of TDC, so they add.
  • Mixing camshaft and crankshaft degrees. 1 camshaft degree = 2 crankshaft degrees.

Hands-on: Draw a valve timing diagram on paper: a circle for one crankshaft revolution with TDC at the top and BDC at the bottom. Using the example in this lesson, draw arcs for the inlet and exhaust open periods in two colors (they spiral over two revolutions) and shade the overlap. Label every angle.

What you will learn

  • I can explain TDC, BDC and the four valve events.
  • I can explain why valves open early and close late.
  • I can calculate valve duration and overlap from a timing diagram.
  • I can explain the effects of overlap at idle and at high rpm.
  • I can explain how variable valve timing works.

Key words

TDC / BDC
Top dead center and bottom dead center: the highest and lowest points of the piston's travel.
valve timing
The crankshaft angles at which the valves open and close.
duration
How long a valve stays open, in crankshaft degrees.
valve overlap
The period around TDC when both the inlet and exhaust valves are open.
variable valve timing (VVT)
A system that changes valve timing while the engine runs.

The big ideas

You might expect each valve to open exactly at the start of its stroke and close exactly at the end. In reality, gases have mass and momentum, and valves take time to open and close. So engine designers open valves early and close them late, measured in degrees of crankshaft rotation either side of top and bottom dead center.

The result is a valve timing diagram: inlet opens before TDC, inlet closes after BDC, exhaust opens before BDC, exhaust closes after TDC. Around TDC, both valves are briefly open – valve overlap. Fixed timing is a compromise between low and high speeds, which is why most modern engines use variable valve timing, controlled by the engine's electronic control module – the part the US Department of Energy describes as controlling the fuel mixture and ignition timing.

This lesson explains the theory and the calculations. Example timings are for practice only.

Read-through: the teaching steps

  1. The four valve events

    • IVO – inlet valve opens, before TDC.
    • IVC – inlet valve closes, after BDC.
    • EVO – exhaust valve opens, before BDC.
    • EVC – exhaust valve closes, after TDC.

    Angles are given in crankshaft degrees, for example 'IVO 12° BTDC'. See the strokes in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. Why open early and close late

    • Inlet opens early so it is well open when the intake stroke begins.
    • Inlet closes late because the incoming air's momentum keeps it flowing as the piston starts to rise.
    • Exhaust opens early to release pressure near the end of the power stroke, when little useful push is left.
    • Exhaust closes late so the outgoing gas can draw the last exhaust out.
  3. Calculating duration

    Duration = degrees open before the dead center + 180° + degrees open after the next dead center.

    Example: IVO 10° BTDC, IVC 40° ABDC: duration = 10 + 180 + 40 = 230°.

  4. Calculating overlap

    Overlap = inlet opening before TDC + exhaust closing after TDC.

    Example: IVO 10° BTDC, EVC 14° ATDC: overlap = 10 + 14 = 24°.

    More overlap helps scavenging at high rpm, but at idle exhaust can flow back into the inlet, making running rough.

  5. Variable valve timing

    VVT changes the timing while the engine runs. A common type is a cam phaser: an oil-pressure actuator that rotates the camshaft a few degrees relative to its sprocket, controlled through an oil control valve by the engine control module. Some systems also change lift by switching between cam profiles. VVT can improve low-speed torque, high-speed power, economy and emissions.

  6. Camshaft and crankshaft degrees

    Because the camshaft turns at half crankshaft speed, 1° at the camshaft equals 2° at the crankshaft. Timing figures in manufacturers' data are normally in crankshaft degrees.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.