The cylinder head and gasket – Motor Vehicle Theory motor mechanics lesson
Lesson 23 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Learn what the cylinder head contains, how the head gasket seals gas, coolant and oil, and why heads distort and gaskets fail.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson explains cylinder heads and gaskets with example figures. The activity is a paper drawing. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think overheating is so damaging to aluminum cylinder heads?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the head gasket only seals coolant. It seals combustion gas, coolant and oil passages.
- Thinking a gasket failure is always obvious from outside. Leaks can be internal – between cylinders or into coolant passages.
- Thinking a new gasket fixes the problem whatever caused it. The cause (overheating, distortion, bolts) must be found too.
Hands-on: Draw a top view of a cylinder head gasket for a four-cylinder engine on paper: four large holes for the bores, small holes for bolts, coolant and oil passages. Color-code what each hole seals. Mark with arrows the leak paths that would give each symptom in this lesson.
What you will learn
- I can describe the parts and functions of a cylinder head.
- I can explain what a head gasket seals and how it works.
- I can explain how overheating distorts heads and causes gasket failure.
- I can relate symptoms to possible gasket failure.
- I can calculate the volume a gasket adds to the combustion chamber.
Key words
- cylinder head
- The part bolted on top of the block that closes the cylinders and carries the valves.
- head gasket
- The seal between head and block for combustion gas, coolant and oil.
- combustion chamber
- The space above the piston at top dead center where combustion takes place.
- port
- A passage in the head carrying air in or exhaust gas out.
- distortion
- Warping of a part, often from overheating, so that it is no longer flat.
The big ideas
The cylinder head is the busiest part of the engine. It closes the top of each cylinder, forms the combustion chambers, carries the inlet and exhaust ports and valves, and on most modern engines holds the camshafts too. The spark plug of a gasoline engine sits in it – the US Department of Energy notes that the spark plug ignites the air–fuel mixture in the combustion chamber.
Between the head and the block sits the head gasket. It must seal combustion pressure in each cylinder and keep coolant and oil in their own passages, all at once, while the engine heats and cools thousands of times.
This lesson explains how the head and gasket work and why they fail. Real limits come from the manufacturer's data, and engine work is done by trained technicians.
Read-through: the teaching steps
The cylinder head
A head contains:
- combustion chambers – shaped to burn the mixture efficiently;
- inlet and exhaust ports – passages for gases;
- valves, springs and guides;
- camshafts on overhead cam engines;
- coolant passages and oil galleries;
- spark plug or injector holes.
See the head above the cylinder in the drawing on the lesson page.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. Materials
Most heads are aluminum alloy: light, and good at carrying heat away from the combustion chamber. Hard valve seats and guides are fitted where the valves touch, because aluminum alone would wear quickly.
The head gasket
The gasket fills the tiny irregularities between head and block. Modern gaskets are usually multi-layer steel (MLS), with raised beads around each bore and passage that are crushed slightly by the head bolts. Its compressed thickness forms part of the combustion chamber volume, so a different thickness changes the compression ratio.
Why heads distort and gaskets fail
Overheating is the usual culprit. Aluminum expands more than iron; severe heat can warp the head, so it no longer clamps the gasket evenly. Gas can then leak between cylinders or into coolant passages. Incorrect bolt tightening and old, stretched bolts are other causes.
Symptoms of gasket failure
- White exhaust vapor and coolant loss – coolant entering a cylinder.
- Overheating, or bubbles in the coolant – combustion gas entering the cooling system.
- Oil and coolant mixing.
- Misfire or low compression in neighboring cylinders.
A technician confirms the cause with tests rather than guessing.
Checks after removal
If a head is removed, technicians check its face and the block face for flatness with a straight edge and feeler gauges, look for cracks, and follow the manufacturer's bolt sequence, stages and angles on refitting – usually with new bolts.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.