▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

The cylinder head and gasket – Motor Vehicle Theory motor mechanics lesson

Lesson 23 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn what the cylinder head contains, how the head gasket seals gas, coolant and oil, and why heads distort and gaskets fail.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains cylinder heads and gaskets with example figures. The activity is a paper drawing. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think overheating is so damaging to aluminium cylinder heads?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the head gasket only seals coolant. It seals combustion gas, coolant and oil passages.
  • Thinking a gasket failure is always obvious from outside. Leaks can be internal – between cylinders or into coolant passages.
  • Thinking a new gasket fixes the problem whatever caused it. The cause (overheating, distortion, bolts) must be found too.

Hands-on: Draw a top view of a cylinder head gasket for a four-cylinder engine on paper: four large holes for the bores, small holes for bolts, coolant and oil passages. Colour-code what each hole seals. Mark with arrows the leak paths that would give each symptom in this lesson.

What you will learn

  • I can describe the parts and functions of a cylinder head.
  • I can explain what a head gasket seals and how it works.
  • I can explain how overheating distorts heads and causes gasket failure.
  • I can relate symptoms to possible gasket failure.
  • I can calculate the volume a gasket adds to the combustion chamber.

Key words

cylinder head
The part bolted on top of the block that closes the cylinders and carries the valves.
head gasket
The seal between head and block for combustion gas, coolant and oil.
combustion chamber
The space above the piston at top dead centre where combustion takes place.
port
A passage in the head carrying air in or exhaust gas out.
distortion
Warping of a part, often from overheating, so that it is no longer flat.

The big ideas

The cylinder head is the busiest part of the engine. It closes the top of each cylinder, forms the combustion chambers, carries the inlet and exhaust ports and valves, and on most modern engines holds the camshafts too. The spark plug of a petrol engine sits in it – the US Department of Energy notes that the spark plug ignites the air–fuel mixture in the combustion chamber.

Between the head and the block sits the head gasket. It must seal combustion pressure in each cylinder and keep coolant and oil in their own passages, all at once, while the engine heats and cools thousands of times.

This lesson explains how the head and gasket work and why they fail. Real limits come from the manufacturer's data, and engine work is done by trained technicians.

Read-through: the teaching steps

  1. The cylinder head

    A head contains:

    • combustion chambers – shaped to burn the mixture efficiently;
    • inlet and exhaust ports – passages for gases;
    • valves, springs and guides;
    • camshafts on overhead cam engines;
    • coolant passages and oil galleries;
    • spark plug or injector holes.

    See the head above the cylinder in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. Materials

    Most heads are aluminium alloy: light, and good at carrying heat away from the combustion chamber. Hard valve seats and guides are fitted where the valves touch, because aluminium alone would wear quickly.

  3. The head gasket

    The gasket fills the tiny irregularities between head and block. Modern gaskets are usually multi-layer steel (MLS), with raised beads around each bore and passage that are crushed slightly by the head bolts. Its compressed thickness forms part of the combustion chamber volume, so a different thickness changes the compression ratio.

  4. Why heads distort and gaskets fail

    Overheating is the usual culprit. Aluminium expands more than iron; severe heat can warp the head, so it no longer clamps the gasket evenly. Gas can then leak between cylinders or into coolant passages. Incorrect bolt tightening and old, stretched bolts are other causes.

  5. Symptoms of gasket failure

    • White exhaust vapour and coolant loss – coolant entering a cylinder.
    • Overheating, or bubbles in the coolant – combustion gas entering the cooling system.
    • Oil and coolant mixing.
    • Misfire or low compression in neighbouring cylinders.

    A technician confirms the cause with tests rather than guessing.

  6. Checks after removal

    If a head is removed, technicians check its face and the block face for flatness with a straight edge and feeler gauges, look for cracks, and follow the manufacturer's bolt sequence, stages and angles on refitting – usually with new bolts.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.