▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Manual transmissions: how gears are selected – Garage Basics motor mechanics lesson

Lesson 19 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out what happens inside a manual transmission when the driver moves the gear lever, and work out overall gear ratios.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

A calculator helps. The two big ideas are that the gears stay meshed while a collar picks one, and that ratios in a row multiply. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think most new cars sold today have automatic transmissions or no transmission at all?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking gears slide in and out of mesh to change gear. In a modern transmission the gears stay meshed. A collar locks the chosen gear to the shaft.
  • Adding the two ratios instead of multiplying. Ratios in a row multiply: 1.5 and 2.5 give 3.75, not 4.
  • Thinking synchromesh changes the gear ratio. Synchromesh only matches speeds so the gear can lock in smoothly. The ratio comes from the teeth.

Hands-on: Draw the H-shaped gear shifter pattern of a five-speed car with reverse. Then make a model: cut three card circles of different sizes, pin them in a row on a cork board or thick card with thumbtacks, and mark an arrow on each. Turn the first one clockwise and watch which way the third one turns. Ask an adult to help with the pins.

What your child will learn

  • I can name the main shafts in a manual transmission.
  • I can explain that the gears are always meshed and a collar locks the chosen one to the shaft.
  • I can explain what synchromesh does.
  • I can calculate an overall ratio from two gear pairs and find the output speed.

Key words

input shaft
The shaft that brings the turning from the clutch into the transmission.
countershaft
A shaft inside the transmission driven by the input shaft. Its gears drive the gears on the output shaft. In the UK it is called the layshaft.
output shaft
The shaft that carries the turning out of the transmission toward the wheels.
synchromesh
A cone-shaped friction ring that matches the speed of a gear and its shaft before they lock together, so the gear change is smooth and quiet.
idler gear
An extra gear placed between two others to make the output turn the opposite way, used for reverse.

The big ideas

A manual transmission lets the driver choose from several gear ratios, usually five or six forward gears and a reverse. The driver presses the clutch pedal, moves the gear shifter, and lifts the clutch again.

Inside, most of the gears are always meshed together. The input shaft turns the countershaft, and each gear on the countershaft turns a matching gear on the output shaft. Those output gears spin freely on their shaft until one is chosen. Moving the gear shifter slides a collar that locks the chosen gear to the output shaft, so only that pair carries the drive.

To stop the teeth of the collar clashing, a synchromesh ring uses friction to bring the gear and the shaft to the same speed first. That is why a modern gear change is smooth and quiet.

Read-through: the teaching steps

  1. Three shafts

    Most car transmissions have an input shaft (from the clutch), a countershaft and an output shaft (toward the wheels). A pair of gears at the front, always meshed, drives the countershaft from the input shaft.

    Driving gear10 teethDriven gear30 teethfast
    Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1.
  2. Gears always in mesh

    Each forward gear is a pair: one gear fixed to the countershaft and one on the output shaft. All the pairs are turning all the time, but the gears on the output shaft spin freely on bearings, so they do not drive anything until one is locked.

  3. Selecting a gear

    Moving the gear shifter moves a selector fork. The fork slides a collar along the output shaft. The collar is splined to the shaft, and teeth on its side (called dogs) lock into the chosen gear. Now that gear and the output shaft turn together.

  4. Synchromesh

    Before the dogs can lock, the gear and the collar must turn at the same speed, or the teeth would clash and grind. A synchromesh ring is a small cone clutch: as the collar moves, the cone rubs on the gear and friction brings the two speeds together. Then the dogs slide in smoothly.

  5. Overall ratio

    The drive passes through two pairs: input shaft to countershaft, then countershaft to output shaft. Ratios in a row multiply:

    overall ratio = first pair ratio × second pair ratio

    Each ratio is driven teeth ÷ driving teeth.

  6. Reverse

    Two meshing gears turn in opposite directions. For reverse, an extra idler gear is slid between a gear on the input side and one on the output side. Three gears in a row make the output turn the other way, so the car goes backward.

  7. Top gear and direct drive

    In many transmissions one gear locks the input shaft straight to the output shaft. That gives a ratio of 1:1, called direct drive. A gear below 1:1, such as 0.8:1, is called an overdrive: the output turns faster than the engine.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Forces, gears and drivetrain lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.