▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Automatic transmissions: the basic idea – Garage Basics motor mechanics lesson

Lesson 20 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how an automatic transmission moves off and changes gear by itself, using a fluid coupling, planetary gears and an electronic control unit.

Time
40 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The fan activity needs an adult and fans with guards. The key idea is that a fluid can carry turning from one wheel to another, which lets a car stand still in gear. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the unplugged fan in the activity turns more slowly than the one that is switched on?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking an automatic has no gears. Most automatics have several gear ratios from planetary gearsets. Only a CVT varies the ratio smoothly without fixed gears.
  • Thinking the torque converter is a set of gears. It is a fluid coupling: oil carries the drive from the impeller to the turbine.
  • Thinking the converter adds torque for free. When torque goes up, the turbine turns more slowly than the impeller. Energy is never created.

Hands-on: With an adult, stand a switched-on desk fan (one with a guard) facing a second, unplugged fan with a guard, about 20 cm apart. Watch the blades of the unplugged fan start to turn. Try moving them closer and further apart. Keep fingers away from both fans. This is the idea of a torque converter, with air in place of oil.

What your child will learn

  • I can explain what a torque converter does in place of a clutch pedal.
  • I can name the parts of a planetary gearset.
  • I can explain how holding different parts of a planetary gearset gives different ratios.
  • I can calculate torque converter slip and torque multiplication.

Key words

torque converter
A fluid coupling between the engine and an automatic transmission. Oil thrown by one fan-like wheel turns another, so the car can stand still with the engine running.
planetary gearset
A set of gears with a sun gear in the middle, planet gears around it on a carrier, and a ring gear with teeth on the inside. It is also called an epicyclic gearset.
slip
The difference in speed between the engine side and the transmission side of a torque converter.
control unit
An electronic computer that reads sensors and decides when to change gear.
selector
The control the driver uses to choose P (park), R (reverse), N (neutral) or D (drive).

The big ideas

An automatic transmission chooses and changes gear by itself. The driver only picks P (park), R (reverse), N (neutral) or D (drive), and there is no clutch pedal.

Two ideas make this work. First, in most traditional automatics a torque converter replaces the clutch. It is a fluid coupling: one wheel of curved blades, driven by the engine, throws oil at a second wheel connected to the transmission. At tickover the oil pushes too gently to move the car, so the car can stand still in gear. As the engine speeds up, the oil pushes harder and the car moves off.

Second, the gear ratios come from planetary gearsets. By holding one part of the gearset still and driving another, the transmission gets different ratios without sliding any gears. Clutches and brake bands inside do the holding, and an electronic control unit decides which to apply, using information such as road speed and how far the gas pedal is pressed.

Read-through: the teaching steps

  1. No clutch pedal

    In an automatic the driver uses only two pedals: gas pedal and brake. The transmission moves off and changes gear by itself. Some automatics use a torque converter, some use two automatic clutches (a dual-clutch transmission), and some use belts and pulleys (a continuously variable transmission, CVT).

  2. The torque converter

    Imagine two fans facing each other. Switch one on and the air it blows turns the other. A torque converter works the same way with oil in a sealed case. The impeller is driven by the engine; the turbine drives the transmission. A third wheel, the stator, redirects the oil so that at low speed the converter multiplies torque, often up to about twice the engine's torque.

  3. Slip and lock-up

    Because the turbine is pushed by oil, it always turns a little slower than the impeller. This slip wastes some energy as heat.

    Slip (%) = (impeller speed − turbine speed) ÷ impeller speed × 100

    At steady cruising many converters close a lock-up clutch that joins the two sides directly, so the slip disappears and fuel is saved.

  4. The planetary gearset

    A planetary gearset has three parts: a sun gear in the center, planet gears that run around it on a planet carrier, and a ring gear with teeth on the inside. All the gears stay meshed all the time.

  5. Holding one part

    A planetary gearset gives a ratio when one part is held still, one is driven and one is the output. For example, hold the ring gear, drive the sun gear and take the output from the carrier: the carrier turns slowly with high torque, which suits a low gear. Lock two parts together and the whole set turns as one: 1:1. Different combinations, using two or more gearsets, give all the gears.

  6. Who decides?

    Inside the transmission, clutches and brake bands hold or join the parts of the gearsets. They are worked by oil pressure. An electronic control unit reads sensors (road speed, engine speed, gas pedal position) and chooses the gear. Repair and fluid work on automatic transmissions is done by trained technicians using the manufacturer's data.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Forces, gears and drivetrain lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.