Manual gearboxes: how gears are selected – Garage Basics motor mechanics lesson
Lesson 19 of 70 in the Garage Basics course (ages 11–16)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out what happens inside a manual gearbox when the driver moves the gear lever, and work out overall gear ratios.
- Time
- 45 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
A calculator helps. The two big ideas are that the gears stay meshed while a collar picks one, and that ratios in a row multiply. Every answer is marked straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think most new cars sold today have automatic gearboxes or no gearbox at all?”
- Later: the homework, then the practice test.
Watch out for
- Thinking gears slide in and out of mesh to change gear. In a modern gearbox the gears stay meshed. A collar locks the chosen gear to the shaft.
- Adding the two ratios instead of multiplying. Ratios in a row multiply: 1.5 and 2.5 give 3.75, not 4.
- Thinking synchromesh changes the gear ratio. Synchromesh only matches speeds so the gear can lock in smoothly. The ratio comes from the teeth.
Hands-on: Draw the H-shaped gear lever pattern of a five-speed car with reverse. Then make a model: cut three card circles of different sizes, pin them in a row on a cork board or thick card with drawing pins, and mark an arrow on each. Turn the first one clockwise and watch which way the third one turns. Ask an adult to help with the pins.
What your child will learn
- I can name the main shafts in a manual gearbox.
- I can explain that the gears are always meshed and a collar locks the chosen one to the shaft.
- I can explain what synchromesh does.
- I can calculate an overall ratio from two gear pairs and find the output speed.
Key words
- input shaft
- The shaft that brings the turning from the clutch into the gearbox.
- layshaft
- A shaft inside the gearbox driven by the input shaft. Its gears drive the gears on the output shaft.
- output shaft
- The shaft that carries the turning out of the gearbox towards the wheels.
- synchromesh
- A cone-shaped friction ring that matches the speed of a gear and its shaft before they lock together, so the gear change is smooth and quiet.
- idler gear
- An extra gear placed between two others to make the output turn the opposite way, used for reverse.
The big ideas
A manual gearbox lets the driver choose from several gear ratios, usually five or six forward gears and a reverse. The driver presses the clutch pedal, moves the gear lever, and lifts the clutch again.
Inside, most of the gears are always meshed together. The input shaft turns the layshaft, and each gear on the layshaft turns a matching gear on the output shaft. Those output gears spin freely on their shaft until one is chosen. Moving the gear lever slides a collar that locks the chosen gear to the output shaft, so only that pair carries the drive.
To stop the teeth of the collar clashing, a synchromesh ring uses friction to bring the gear and the shaft to the same speed first. That is why a modern gear change is smooth and quiet.
Read-through: the teaching steps
Three shafts
Most car gearboxes have an input shaft (from the clutch), a layshaft and an output shaft (towards the wheels). A pair of gears at the front, always meshed, drives the layshaft from the input shaft.
Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1. Gears always in mesh
Each forward gear is a pair: one gear fixed to the layshaft and one on the output shaft. All the pairs are turning all the time, but the gears on the output shaft spin freely on bearings, so they do not drive anything until one is locked.
Selecting a gear
Moving the gear lever moves a selector fork. The fork slides a collar along the output shaft. The collar is splined to the shaft, and teeth on its side (called dogs) lock into the chosen gear. Now that gear and the output shaft turn together.
Synchromesh
Before the dogs can lock, the gear and the collar must turn at the same speed, or the teeth would clash and grind. A synchromesh ring is a small cone clutch: as the collar moves, the cone rubs on the gear and friction brings the two speeds together. Then the dogs slide in smoothly.
Overall ratio
The drive passes through two pairs: input shaft to layshaft, then layshaft to output shaft. Ratios in a row multiply:
overall ratio = first pair ratio × second pair ratio
Each ratio is driven teeth ÷ driving teeth.
Reverse
Two meshing gears turn in opposite directions. For reverse, an extra idler gear is slid between a gear on the input side and one on the output side. Three gears in a row make the output turn the other way, so the car goes backwards.
Top gear and direct drive
In many gearboxes one gear locks the input shaft straight to the output shaft. That gives a ratio of 1:1, called direct drive. A gear below 1:1, such as 0.8:1, is called an overdrive: the output turns faster than the engine.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Forces, gears and drivetrain lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.