▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Pressure: measurement, isobars, QNH, QFE and the standard setting – Private Pilot Theory aviation lesson

Lesson 75 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

How air pressure is measured and mapped with isobars, and how the altimeter setting and the standard setting of 29.92 inHg change what an altimeter reads.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). The UK and US systems use different words and units; each page teaches its own country's version. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might it matter that every aircraft above a certain height uses exactly the same pressure setting, even though the real sea-level pressure is different?”
  4. Later: the homework, then the practice test.

Watch out for

  • Getting the sign wrong in the pressure altitude rule. Work out 29.92 minus the setting. A setting above 29.92 gives a negative correction, so pressure altitude is below the field elevation.
  • Reading close isobars as 'calm'. Close isobars mean a steep pressure gradient – strong wind.
  • Forgetting that the setting changes from place to place. Below 18,000 ft the AIM describes using a current setting from a station within 100 NM along the route.

Hands-on: Draw two sets of curved lines on paper: one set 1 cm apart, the other 3 cm apart. Label them as isobars every 4 units and mark where you think the wind would be strongest. Then hold a sheet of paper flat and blow gently across it at different distances to feel how a steeper 'slope' gives a stronger push.

What you will learn

  • I can explain how pressure is measured and why station pressure is corrected to sea level.
  • I can read isobars and say what close or wide spacing means.
  • I can say what the local altimeter setting and the standard setting (29.92 inHg) each make the altimeter show.
  • I can work out pressure altitude from field elevation and the altimeter setting using 1,000 ft per inHg.

Key words

barometer
An instrument that measures air pressure – traditionally a mercury column, now usually a sealed aneroid cell.
isobar
A line on a weather chart joining places with equal sea-level pressure.
pressure gradient
How quickly pressure changes with distance; close isobars mean a steep gradient and strong wind.
altimeter setting
The reported setting that makes the altimeter show altitude above mean sea level (the US name for what ICAO calls QNH).
standard setting
29.92 inHg, set at and above 18,000 ft MSL so that the altimeter shows pressure altitude (flight levels).

The big ideas

Air pressure is the weight of the air above you. It used to be measured with a mercury barometer; most instruments now use a sealed aneroid cell. Because pressure falls with height, every weather station converts its reading to sea level – the FAA handbook says by adding about 1 inHg for every 1,000 ft of elevation – so stations at different elevations can be compared. Lines joining equal sea-level pressure are isobars. Closely spaced isobars mean a steep pressure gradient and strong winds; wide spacing means light winds. Highs, lows, ridges (long areas of high pressure) and troughs (long areas of low pressure) all show up as isobar patterns.

An altimeter is a barometer marked in feet, so it needs a starting pressure. The FAA's Aeronautical Information Manual describes the US system: below 18,000 ft MSL the altimeter is set to a current reported altimeter setting from a station along the route and within 100 NM; at or above 18,000 ft MSL everyone sets the standard 29.92 inHg, and the altimeter then shows pressure altitude, used as flight levels. ICAO calls the local setting QNH; the US simply calls it the altimeter setting.

The handbook's rule of thumb is that 1 inHg is about 1,000 ft. That lets you work out pressure altitude from the field elevation and the altimeter setting.

Read-through: the teaching steps

  1. Measuring pressure

    A mercury barometer balances a column of mercury against the weight of the air; an aneroid barometer uses a sealed, partly evacuated metal cell that squeezes or expands as pressure changes. The altimeter in an aircraft is an aneroid barometer marked in feet.

  2. Correcting to sea level

    A station on a hill always reads lower pressure than one at the coast, even on the same day. So each station converts its reading to sea level, adding about 1 inHg per 1,000 ft of elevation (FAA handbook). Only then can the readings be plotted together on one chart.

  3. Isobars

    Isobars join places with equal sea-level pressure.

    • Close together: steep pressure gradient, strong wind
    • Far apart: shallow gradient, light wind
    • High: pressure higher than all around; low: lower than all around
    • Ridge: long tongue of high pressure; trough: long tongue of low pressure
  4. The altimeter setting – altitude above sea level

    With the current altimeter setting set, the altimeter shows altitude above mean sea level. On the ground it should read the field elevation. The FAA handbook notes the setting is accurate only near the reporting station, so it is updated en route.

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 29.92 inHgAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  5. Field elevation and the 1,000 ft rule

    Because 1 inHg is about 1,000 ft, the difference between the local setting and 29.92 tells you how far pressure altitude is from the field elevation:

    Pressure altitude ≈ field elevation + (29.92 − altimeter setting) × 1,000 ft.

  6. The standard setting and flight levels

    At or above 18,000 ft MSL the altimeter is set to 29.92 inHg. Everyone then measures from the same datum, and levels are given as flight levels: FL180 means 18,000 ft on the standard setting.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: FAA Pilot’s Handbook of Aeronautical Knowledge, chapter 8: flight instruments (free PDF) (opens in a new tab).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Meteorology lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.