▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Pressure: measurement, isobars, QNH, QFE and the standard setting – Private Pilot Theory aviation lesson

Lesson 75 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

How air pressure is measured and mapped with isobars, and how the pressure settings QNH, QFE and the standard setting change what an altimeter reads.

Time
45 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). The UK and US systems use different words and units; each page teaches its own country's version. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might it matter that every aircraft above a certain height uses exactly the same pressure setting, even though the real sea-level pressure is different?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking QFE is higher than QNH at an aerodrome above sea level. Higher ground means less air above it, so lower pressure: QFE is the smaller number.
  • Reading close isobars as 'calm'. Close isobars mean a steep pressure gradient – strong wind.
  • Leaving QNH set after climbing above the transition altitude. In theory, above the transition altitude everyone uses 1013 hPa so their levels are measured from the same datum.

Hands-on: Draw two sets of curved lines on paper: one set 1 cm apart, the other 3 cm apart. Label them as isobars every 4 units and mark where you think the wind would be strongest. Then hold a sheet of paper flat and blow gently across it at different distances to feel how a steeper 'slope' gives a stronger push.

What you will learn

  • I can explain how pressure is measured and why station pressure is corrected to sea level.
  • I can read isobars and say what close or wide spacing means.
  • I can say what QNH, QFE and the standard setting (1013 hPa) each make the altimeter show.
  • I can work out a QFE from a QNH and the aerodrome elevation using 27 ft per hPa.

Key words

barometer
An instrument that measures air pressure – traditionally a mercury column, now usually a sealed aneroid cell.
isobar
A line on a weather chart joining places with equal sea-level pressure.
pressure gradient
How quickly pressure changes with distance; close isobars mean a steep gradient and strong wind.
QNH
The pressure setting that makes the altimeter show altitude above mean sea level.
QFE
The pressure setting that makes the altimeter show height above the aerodrome; it reads zero on the runway.

The big ideas

Air pressure is the weight of the air above you. It used to be measured with a mercury barometer; most instruments now use a sealed aneroid cell. Because pressure falls with height, every weather station converts its reading to the equivalent sea-level value so that stations at different elevations can be compared. Lines joining equal sea-level pressure are isobars. The FAA handbook explains that closely spaced isobars mean a steep pressure gradient and strong winds; wide spacing means light winds. Highs, lows, ridges (long areas of high pressure) and troughs (long areas of low pressure) all show up as isobar patterns.

An altimeter is a barometer marked in feet, so it needs a starting pressure. The CAA's Skyway Code describes the UK settings: QNH makes the altimeter show altitude above mean sea level; QFE makes it show height above the aerodrome, so it reads zero on the runway; and the standard setting of 1013 hPa, used above the transition altitude, gives flight levels. Outside controlled airspace the UK transition altitude is 3,000 ft.

Near the ground, 1 hPa is about 27 ft (Skyway Code). That simple figure lets you convert between QNH and QFE, and between pressure differences and heights.

Read-through: the teaching steps

  1. Measuring pressure

    A mercury barometer balances a column of mercury against the weight of the air; an aneroid barometer uses a sealed, partly evacuated metal cell that squeezes or expands as pressure changes. The altimeter in an aircraft is an aneroid barometer marked in feet.

  2. Correcting to sea level

    A station on a hill always reads lower pressure than one at the coast, even on the same day. So each station converts its reading to a sea-level value. Only then can the readings be plotted together on one chart.

  3. Isobars

    Isobars join places with equal sea-level pressure.

    • Close together: steep pressure gradient, strong wind
    • Far apart: shallow gradient, light wind
    • High: pressure higher than all around; low: lower than all around
    • Ridge: long tongue of high pressure; trough: long tongue of low pressure
  4. QNH – altitude above sea level

    With QNH set, the altimeter shows altitude above mean sea level. On the ground it should read the aerodrome elevation. Heights of hills and obstacles on charts are given above sea level, so QNH lets the two be compared.

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 1013.25 hPaAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  5. QFE – height above the aerodrome

    With QFE set, the altimeter shows height above the aerodrome and reads zero on the runway. QFE is always lower than QNH at an aerodrome above sea level, by about 1 hPa for every 27 ft of elevation.

    QFE ≈ QNH − elevation ÷ 27.

  6. The standard setting and flight levels

    Above the transition altitude (3,000 ft outside controlled airspace in the UK; the figure differs near some airports) the altimeter is set to 1013 hPa. Everyone then measures from the same datum, and levels are given as flight levels: FL35 means 3,500 ft on the standard setting.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: CAA Skyway Code (CAP 1535) (opens in a new tab).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Meteorology lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.