▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Motorcycle tyres, wheels and the law – Vehicles and Technology motor mechanics lesson

Lesson 18 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out why motorcycle tyres are round in profile, how wheels and tyres are built, and what UK law and the MOT say about motorcycle tread.

Time
45 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

The card model needs scissors and a table. Tyre fitting and inflation on a motorcycle are jobs for trained people; any look at a real machine is look-only. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Two small contact patches hold a motorcycle up. What does that tell you about how carefully riders should treat their tyres?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking motorcycle tyres should be flat like car tyres. A flat tread would lose its contact patch as soon as the bike leaned; the rounded profile keeps grip at every lean angle.
  • Using the maximum pressure printed on the sidewall as the pressure to run. The sidewall shows a maximum, not the correct figure; the motorcycle maker's handbook gives the pressures to use.
  • Thinking tread only needs checking in the centre of the tyre. Tread is judged across a wide band all the way round; a tyre can be worn on one part of the circumference.

Hands-on: Cut a circle and a rounded "tyre" profile from card. Roll the profile on a table at different lean angles and mark where it touches. Then, with an adult, look at the sidewall of a bicycle tyre and find the size and any date or pressure markings. If you see a motorcycle, look only while it is parked, switched off and cold.

What you will learn

  • I can explain why motorcycle tyres have a rounded profile.
  • I can compare cast and spoked wheels, and tubed and tubeless tyres.
  • I can read the main markings on a motorcycle tyre sidewall.
  • I can state the UK minimum tread for motorcycles and mopeds and where it is measured.
  • I can explain why pressure must be checked cold using the maker's figure.

Key words

profile
The shape of the tyre seen in cross-section; motorcycle tyres are rounded so they can lean.
contact patch
The small area of tyre actually touching the road.
tubeless
A tyre that seals directly against the rim with no inner tube.
cast wheel
A wheel made in one piece of cast alloy, usually with tubeless tyres.
spoked wheel
A wheel with a rim joined to the hub by wire spokes; often used with an inner tube.
tread band
The part of the tread width over which minimum depth is measured.

The big ideas

A car tyre has a flat tread because a car stays upright. A motorcycle leans into every bend, so its tyres have a rounded profile: as the bike leans, the contact patch rolls round from the centre of the tread to the shoulder. The whole machine is held up and steered by two contact patches, each about the size of a credit card, so the condition of the tyres matters enormously.

Wheels come in two main kinds: cast alloy wheels, usually with tubeless tyres, and spoked wheels, often used on off-road and classic bikes and often with inner tubes. The sidewall carries the size, load and speed markings and the date the tyre was made.

In the UK the law and the MOT set a minimum tread depth. GOV.UK says motorcycles need at least 1 mm of tread and mopeds a visible tread, and riding a vehicle in a dangerous condition can bring a fine of up to £2,500, a ban and 3 penalty points. Tyre fitting and inflation are jobs for trained people: this lesson explains, it does not instruct.

Read-through: the teaching steps

  1. Why the profile is round

    When a motorcycle leans, it does not slide sideways because the tyre grips at an angle. The rounded profile keeps a contact patch on the road at every lean angle. Many sports tyres use harder rubber in the centre (for long life on straight roads) and softer rubber at the shoulders (for grip when leaning).

    Tread depthat least 1.6 mmCentral three-quarters of the treadTread blockGroove
    Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round.
  2. Cast and spoked wheels

    • Cast alloy wheels: one piece, stiff and air-tight, so they can use tubeless tyres
    • Spoked wheels: a rim laced to the hub with wire spokes; flexible and easy to repair after knocks, which suits off-road riding, but the spoke holes mean many need an inner tube
  3. Reading the sidewall

    A motorcycle tyre sidewall shows the width, the profile (aspect ratio), the construction (R for radial) and the rim diameter in inches, followed by the load index and speed symbol – for example 180/55 R17 73W. It also shows a direction-of-rotation arrow and a date code: the last four digits of the identification number give the week and year of manufacture. The sidewall drawing on the lesson page shows where these sit.

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tyre size code.
  4. Pressure matters

    Too little pressure lets the tyre flex and overheat, makes steering heavy and can let the tyre move on the rim. Too much shrinks the contact patch and reduces grip. The correct figures come from the motorcycle maker's handbook, and pressure is judged when the tyre is cold, because a warm tyre reads higher.

  5. UK tread law and the MOT

    As of November 2026 the DVSA MOT inspection manual for motorcycles requires at least 1.0 mm of tread throughout a single band covering at least three-quarters of the tread breadth, all the way round. For machines up to 50 cc a visible tread pattern is required. Below this is a Dangerous defect. GOV.UK gives the same rule for riders: motorcycles 1 mm, mopeds a visible tread.

  6. Safety

    Tyres and wheels are safety-critical. Fitting, balancing, repairing and inflating motorcycle tyres is done by trained technicians with the right equipment and eye protection. When looking at a real motorcycle, an adult is present, the bike is parked on its stand, switched off and cold, and you look only.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Motorcycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.