▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Motorcycle tires and wheels – Vehicles and Technology motor mechanics lesson

Lesson 18 of 50 in the Vehicles and Technology course (ages 14+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out why motorcycle tires are round in profile, how wheels and tires are built, and what US riders need to know about tread, pressure and tire age.

Time
45 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

The card model needs scissors and a table. Tire fitting and inflation on a motorcycle are jobs for trained people; any look at a real machine is look-only. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Two small contact patches hold a motorcycle up. What does that tell you about how carefully riders should treat their tires?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking motorcycle tires should be flat like car tires. A flat tread would lose its contact patch as soon as the bike leaned; the rounded profile keeps grip at every lean angle.
  • Using the maximum pressure printed on the sidewall as the pressure to run. The sidewall shows a maximum, not the correct figure; the motorcycle maker's handbook gives the pressures to use.
  • Thinking tread only needs checking in the center of the tire. Tread is judged across a wide band all the way round; a tire can be worn on one part of the circumference.

Hands-on: Cut a circle and a rounded "tire" profile from card. Roll the profile on a table at different lean angles and mark where it touches. Then, with an adult, look at the sidewall of a bicycle tire and find the size and any date or pressure markings. If you see a motorcycle, look only while it is parked, switched off and cold.

What you will learn

  • I can explain why motorcycle tires have a rounded profile.
  • I can compare cast and spoked wheels, and tubed and tubeless tires.
  • I can read the main markings on a motorcycle tire sidewall.
  • I can explain how tread is measured in 32nds of an inch and why US rules depend on the state.
  • I can explain why pressure must be checked cold using the maker's figure.

Key words

profile
The shape of the tire seen in cross-section; motorcycle tires are rounded so they can lean.
contact patch
The small area of tire actually touching the road.
tubeless
A tire that seals directly against the rim with no inner tube.
cast wheel
A wheel made in one piece of cast alloy, usually with tubeless tires.
spoked wheel
A wheel with a rim joined to the hub by wire spokes; often used with an inner tube.
tread band
The part of the tread width over which minimum depth is measured.

The big ideas

A car tire has a flat tread because a car stays upright. A motorcycle leans into every bend, so its tires have a rounded profile: as the bike leans, the contact patch rolls round from the center of the tread to the shoulder. The whole machine is held up and steered by two contact patches, each about the size of a credit card, so the condition of the tires matters enormously.

Wheels come in two main kinds: cast alloy wheels, usually with tubeless tires, and spoked wheels, often used on off-road and classic bikes and often with inner tubes. The sidewall carries the size, load and speed markings and the date the tire was made.

In the US, rules on tread and inspections are set by each state, and the motorcycle maker's handbook gives the correct pressures. Tire fitting and inflation are jobs for trained people: this lesson explains, it does not instruct.

Read-through: the teaching steps

  1. Why the profile is round

    When a motorcycle leans, it does not slide sideways because the tire grips at an angle. The rounded profile keeps a contact patch on the road at every lean angle. Many sports tires use harder rubber in the center (for long life on straight roads) and softer rubber at the shoulders (for grip when leaning).

    Tread depthreplace at 2/32 inTread wear barTread blockGroove
    Tread depth is measured in the grooves. NHTSA says a tire should be replaced when the tread is worn down to 2/32 of an inch.
  2. Cast and spoked wheels

    • Cast alloy wheels: one piece, stiff and air-tight, so they can use tubeless tires
    • Spoked wheels: a rim laced to the hub with wire spokes; flexible and easy to repair after knocks, which suits off-road riding, but the spoke holes mean many need an inner tube
  3. Reading the sidewall

    A motorcycle tire sidewall shows the width, the profile (aspect ratio), the construction (R for radial) and the rim diameter in inches, followed by the load index and speed symbol – for example 180/55 R17 73W. It also shows a direction-of-rotation arrow and a date code: the last four digits of the identification number give the week and year of manufacture. The sidewall drawing on the lesson page shows where these sit.

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tire size code.
  4. Pressure matters

    Too little pressure lets the tire flex and overheat, makes steering heavy and can let the tire move on the rim. Too much shrinks the contact patch and reduces grip. The correct figures come from the motorcycle maker's handbook, and pressure is judged when the tire is cold, because a warm tire reads higher.

  5. Tread depth in the US

    US tread depth is measured in 32nds of an inch. There is no single national tread limit for motorcycles in use: each state sets its own inspection and equipment rules, and many states do not inspect motorcycles at all. Riders follow their state's rules and the tire maker's wear indicators – small raised bars in the grooves that show when the tread is worn down.

  6. Safety

    Tires and wheels are safety-critical. Fitting, balancing, repairing and inflating motorcycle tires is done by trained technicians with the right equipment and eye protection. When looking at a real motorcycle, an adult is present, the bike is parked on its stand, switched off and cold, and you look only.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Motorcycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

About this lesson

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.