▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Motorcycle suspension and steering – Vehicles and Technology motor mechanics lesson

Lesson 19 of 50 in the Vehicles and Technology course (ages 14+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how forks, swinging arms, springs and damping keep a motorcycle's tyres on the road, and how rake, trail and countersteering make it steer.

Time
45 minutes + 10 min homework
Course
Vehicles and Technology (ages 14+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

The spring experiment needs only a spring or rubber band and some small weights. Any bicycle riding should be on a quiet, safe path with a helmet; motorcycles are look-only, parked and switched off. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think racing motorcycles and off-road motorcycles have such different suspension?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the spring stops the bouncing. The spring stores energy and would bounce on its own; damping turns that energy into heat and stops the bouncing.
  • Thinking you turn a motorcycle at speed only by leaning your body. Body lean helps, but the turn is started by countersteering through the handlebars.
  • Thinking stiffer suspension always means better grip. Suspension that is too stiff lets the tyre skip over bumps; the tyre must stay pressed on the road.

Hands-on: Hang a small weight from a spring or rubber band and measure how far it stretches for 1, 2 and 3 weights; plot a graph to check Hooke's law. Then push an office chair and watch how its castor wheels swing round to trail behind – that is the same idea as motorcycle trail. With an adult, a bicycle ridden slowly on a quiet path can show countersteering.

What you will learn

  • I can explain the different jobs of springs and damping.
  • I can describe telescopic forks, upside-down forks and single and twin rear units.
  • I can use Hooke's law to work out how far a spring compresses.
  • I can explain what rake and trail do for stability.
  • I can describe countersteering in simple terms.

Key words

telescopic forks
Two sliding tubes at the front that hold the front wheel, contain springs and damping, and turn for steering.
damping
Resistance to movement, made by pushing oil through small holes, that stops the bike bouncing.
preload
How much a spring is already squeezed before the bike's weight goes on it.
rake
The angle of the steering axis back from vertical.
trail
The distance on the ground between where the steering axis meets the road and the centre of the contact patch.
countersteering
Briefly pushing the handlebar the "wrong" way to make the bike lean and turn.

The big ideas

A motorcycle's suspension has two jobs: keep the tyres pressed onto the road over bumps, and keep the bike stable and comfortable. Each end uses a spring, which stores the energy of a bump, and damping, which turns that energy into heat so the bike does not keep bouncing.

At the front, telescopic forks slide in and out and also form the steering. At the back, the swinging arm pivots on the frame and is held up by one or two suspension units (shock absorbers). The angle of the forks and a measurement called trail give the steering its self-centring stability, and riders turn a motorcycle by a surprising method called countersteering.

In the UK the MOT inspection manual for motorcycles checks the suspension with the wheels and tyres, and has a steering section covering the handlebars, forks and yokes; stiff, notchy or worn steering head bearings are a Major defect, and Dangerous if steering control is affected. This is explanation for understanding: suspension springs store a lot of energy, and suspension and steering work is only for trained technicians.

Read-through: the teaching steps

  1. Springs and damping

    A spring alone would let the bike bounce up and down like a ball. Damping slows the movement: oil is forced through small holes (valves) inside the fork or suspension unit, turning the movement energy into heat.

    • Compression damping: controls how fast the suspension squashes
    • Rebound damping: controls how fast it stretches back out
  2. Front forks

    Conventional telescopic forks have thin stanchion tubes at the top sliding inside thicker sliders at the bottom. Upside-down (USD) forks put the thick tubes at the top, clamped in the yokes, which makes them stiffer and reduces the weight that moves with the wheel. The yokes (triple clamps) hold both legs and turn in the steering head bearings.

  3. Rear suspension

    The swinging arm pivots on the frame. Older and classic bikes use two suspension units, one each side. Most modern bikes use a single unit (monoshock), often with a linkage that makes the suspension firmer the further it moves – soft over small bumps, firm over big ones.

  4. Hooke's law at work

    A coil spring obeys Hooke's law within its limits:

    force = spring rate × compression (F = k × x)

    A spring of rate 20 N/mm squashes 100 mm under 2,000 N. "Sag" is how far the bike sinks under its own weight and the rider's; the maker's data gives the recommended figure.

  5. Rake and trail

    The steering axis leans back at an angle – the rake. Because of this, the point where the axis meets the road is in front of the tyre's contact patch. The gap is the trail. Like the castor wheels on an office chair, trail makes the front wheel want to follow straight behind its steering axis, which gives stability. More trail: steadier but slower steering; less trail: quicker but more nervous.

    SaddleHandlebarsFramePedal and crankChainRear wheel and tyreFront wheelBrake
    The main parts of a bicycle.
  6. Countersteering

    Above walking pace, a rider starts a right turn by briefly pushing the right handlebar forward – steering the front wheel a little to the left. The tyres move out from under the bike, so it leans to the right, and the lean makes it turn right. Riders do this almost without thinking. Cyclists do it too.

  7. What the MOT looks at

    The MOT inspection manual for motorcycles groups the steering checks as mechanical condition; handlebar, forks and yokes; and wheel alignment. Stiff, notchy or worn steering head bearings are Major, or Dangerous if steering control is affected. A missing handgrip is Major; an insecure one is Dangerous. Suspension is checked with the wheels and tyres. Testers and technicians do this work; learners only look.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Motorcycles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.