Electric motors: how they turn electricity into motion – Vehicles and Technology motor mechanics lesson
Lesson 3 of 50 in the Vehicles and Technology course (ages 14+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Discover the physics that makes an electric car move – the force on a current in a magnetic field – and how the two main kinds of traction motor, permanent-magnet and induction, put it to work.
- Time
- 45 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
The compass test uses one AA cell with a bulb in the circuit and short taps of the switch. Nothing in this lesson involves a real car. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think some makers choose motors with no permanent magnets, even though magnet motors are usually more efficient?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the motor is fed with DC straight from the battery. Most traction motors run on three-phase AC. The inverter in the power electronics makes it from the battery's DC.
- Thinking a motor only works one way. The same machine can be a motor (electricity in, motion out) or a dynamo (motion in, electricity out).
- Thinking a reduction gear adds power. A gear trades speed for torque. Power stays the same apart from small losses.
Hands-on: Make a simple compass test: place a magnetic compass next to a straight piece of wire in a simple circuit with a single AA cell, a small bulb in a holder and a switch, with an adult helping. Close the switch for a second at a time and watch the needle move – the current makes a magnetic field. Then draw a stator with three coils labelled A, B and C and shade which coil is strongest at each of six moments to show how the field "goes round". Use only one household AA cell with the bulb in the circuit, keep each test short, and never use a car battery.
What you will learn
- I can explain the motor effect: a current-carrying wire in a magnetic field feels a force.
- I can describe the stator and rotor and how a rotating magnetic field turns the rotor.
- I can compare permanent-magnet and induction traction motors.
- I can calculate power from torque and speed, and use a reduction gear ratio.
- I can explain why a motor can also work as a dynamo.
Key words
- motor effect
- A wire carrying a current in a magnetic field feels a force. This force is what turns an electric motor.
- stator
- The fixed outer part of a motor, holding coils of copper wire.
- rotor
- The part of a motor that spins, joined to the output shaft.
- rotating magnetic field
- A magnetic field made by the stator coils that sweeps round in a circle when they are fed with three-phase AC.
- torque
- Turning force, measured in newton-metres (N m).
- permanent-magnet motor
- A motor whose rotor carries strong permanent magnets that are pulled round by the stator's rotating field.
- induction motor
- A motor whose rotor has no magnets; the rotating field induces currents in the rotor, which then turn with it.
The big ideas
Every electric car relies on one piece of physics: a wire carrying an electric current in a magnetic field feels a force. Wind the wire into coils, arrange the coils round a shaft, and that force becomes a steady turning force – torque.
A traction motor has two main parts. The stator is fixed and carries coils of copper wire. The rotor spins inside it. The car's power electronics feed the stator coils with three-phase alternating current, which creates a magnetic field that sweeps round the stator. The rotor is dragged round by that rotating field. Change the frequency of the current and you change the speed of the field, and so the speed of the motor.
Two designs are common. In a permanent-magnet motor the rotor carries strong magnets. In an induction motor the rotor has no magnets: the rotating field induces currents in it, and those currents make the rotor follow the field. Both can work in reverse, as a dynamo, when the wheels turn the motor – that is how regenerative braking recovers energy.
This is explanation for understanding, not a repair guide. Traction motors are part of the high-voltage system, and their magnets can make a motor produce a dangerous voltage if the wheels are turned, so they are for trained technicians only.
Read-through: the teaching steps
The motor effect
Put a wire between the poles of a magnet and pass a current through it: the wire is pushed sideways. The force is bigger when the current is bigger, the magnetic field is stronger, or more wire sits in the field.
In GCSE physics this is written F = B I L (force = magnetic flux density × current × length of wire). A motor uses many turns of wire to multiply the effect.
Stator and rotor
The stator is the fixed outer ring, packed with copper coils set in thin steel sheets. The rotor sits in the middle on bearings and is joined to the output shaft.
The gap between them is very small, so the magnetic field crosses it strongly. Look at the electric car layout in the drawing on the lesson page to see where the motor sits between the wheels.
The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only. A field that goes round
The stator has three sets of coils. The power electronics feed them with three-phase AC – three currents that rise and fall one after another. The result is a magnetic field that sweeps round the stator like a lighthouse beam.
The faster the AC alternates (its frequency), the faster the field turns, and the faster the rotor turns. Making the currents bigger gives more torque.
Permanent-magnet motors
In a permanent-magnet synchronous motor, the rotor carries strong magnets. They lock on to the rotating field and turn at exactly the same speed as it – "synchronous" means in step.
These motors are compact and very efficient, which is why many electric cars use them. Their magnets are always magnetic, so a spinning rotor always makes a voltage in the coils.
Induction motors
An induction motor's rotor is a cage of metal bars with no magnets. As the stator's field sweeps past the bars it induces currents in them, and those currents make their own magnetic field that is dragged round after the stator's field.
The rotor always turns slightly slower than the field – this difference is called slip – because without slip no current would be induced. Induction motors need no magnets and make no voltage when they spin freely with the power off.
Torque, speed and gearing
An electric motor gives strong torque from a standstill and keeps working over a very wide speed range, so most electric cars use a single reduction gear. A reduction gear multiplies torque and divides speed by its ratio.
- Wheel torque = motor torque × gear ratio
- Wheel speed = motor speed ÷ gear ratio
- Power (W) = torque (N m) × angular speed (rad/s), and angular speed = rpm × 2π ÷ 60
Motor and dynamo in one
Turn a motor's shaft by force and it makes electricity: it works as a dynamo. When an electric car slows down, the wheels drive the motor, which sends energy back to the battery.
This is also a safety point. The UK Health and Safety Executive (HSE) warns of unexpected movement from motor magnets and advises avoiding towing an electric car unless it is confirmed safe, because turning wheels can make a dangerous voltage. Only trained technicians work on traction motors.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electric and hybrid vehicles lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do all-electric cars work?
- HSE – Electric and hybrid vehicles
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.