Wheel alignment: measuring and adjusting (theory) – Motor Vehicle Theory motor mechanics lesson
Lesson 82 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
See how a workshop measures a car's wheel angles, why worn parts must be found before anything is set, and which angles can usually be adjusted and which cannot.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The calculations use inverse tan, so a scientific calculator is useful. Alignment is skilled work on safety-critical systems using raised vehicles; this lesson explains the ideas only. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think a workshop measures the rear wheels first in a four-wheel alignment, even when it is the front wheels that steer?”
- Later: the homework, then the practice test.
Watch out for
- Thinking an alignment will cure a car with worn joints. Worn joints let the angles change while driving. They must be put right before the angles are measured and set.
- Thinking every angle can be adjusted. On many cars only front toe can be set. If camber or castor is wrong on a car where they are fixed, a part is bent and must be replaced.
- Thinking a straight steering wheel proves the alignment is right. The wheel can be straight while camber or rear toe is wrong. Only measuring all the angles shows that.
Hands-on: Model toe with two toy cars or two equal books on a table: point their fronts slightly towards each other, then measure the gap at the front and at the back with a ruler. Work out the toe distance and convert it to an angle using the width of the "wheel". Then look at an alignment printout if one is available from a family car's service paperwork, and find which figures were in or out of specification. Do not try to measure or adjust a real car.
What you will learn
- I can explain why a car needs a wheel alignment check and what normally prompts one.
- I can describe the checks a technician makes before measuring the angles.
- I can explain how alignment equipment measures toe, camber and castor, and what thrust angle means.
- I can say which angles are commonly adjustable and why a bent part is replaced rather than adjusted.
- I can convert a toe measurement in millimetres into an angle.
Key words
- wheel alignment
- Measuring the steering and suspension angles of all the wheels and setting them to the manufacturer's figures.
- four-wheel alignment
- An alignment that measures the rear wheels as well as the front, and sets the front wheels to the direction the rear wheels are actually pointing.
- thrust angle
- The direction the rear wheels push the car, compared with the car's centre line. If it is not zero, the car "crabs" slightly and the steering wheel sits off-centre.
- turning plates
- Rotating plates marked in degrees that the front wheels stand on, so they can be steered freely during measurement.
- castor sweep
- Steering the front wheels a set amount each way while the equipment watches how camber changes; castor is worked out from that change.
The big ideas
This is explanation for understanding, not a repair guide. Wheel alignment is done by trained technicians with special equipment and the manufacturer's data.
The angles you met earlier – toe, camber, castor and kingpin inclination – are set when a car is built, but they can change. A heavy knock against a kerb, a pothole, worn joints or new steering and suspension parts can all move them. When they are wrong, the car may pull, the steering wheel may sit crooked and the tyres may wear quickly.
A wheel alignment measures every angle and compares it with the manufacturer's figures. Some angles can then be set; others are fixed by the shape of the parts, and if they are wrong a part is bent and must be replaced. This lesson explains how the measurement works and why the order of the job matters.
Read-through: the teaching steps
When alignment is checked
A technician is likely to check the alignment when:
- tyres are wearing unevenly – one shoulder, or feathered tread;
- the car pulls to one side or the steering wheel is not straight;
- the car has hit a kerb or a deep pothole;
- steering or suspension parts such as track rods or arms have been replaced.
A check is also common when new tyres are fitted, so they are not worn out quickly by a fault.
Checks before measuring
Measuring angles on a worn car gives misleading results, so the technician first checks:
- tyre pressures and that the tyres on each axle are a matching size;
- the ride height, as sagging springs change the angles;
- the steering and suspension joints and bushes for play;
- the wheels for damage.
Worn or damaged parts are dealt with first. There is no point setting the toe on a car with a loose ball joint, because it will change as soon as the car is driven.
How the angles are measured
The car stands on a level alignment ramp, with the front wheels on turning plates and the rear wheels on slip plates so the suspension can settle. Sensors or targets are clamped to each wheel, and cameras or laser heads measure their exact position.
- Toe and camber are read directly with the wheels straight ahead.
- Castor cannot be seen directly. The equipment measures it with a castor sweep: the wheels are steered a set amount each way, and castor is worked out from how the camber changes.
- Kingpin inclination and included angle are worked out in a similar way.
Two-wheel and four-wheel alignment
The rear wheels also have toe and camber. Together their toe sets the thrust angle – the direction the rear axle pushes the car. If it is not zero, the car moves slightly sideways, like a crab, and the driver holds the steering a little off-centre to go straight.
In a four-wheel alignment the rear wheels are measured (and set, if they are adjustable) first. The front toe is then set to the thrust line, so the steering wheel is straight when the car goes straight. In this calculation, thrust angle is half the difference between the two rear wheels' individual toe angles.
What can be adjusted
On most cars:
- front toe is adjustable, by changing the effective length of the track rods;
- rear toe and camber are adjustable on some cars, with eccentric bolts or slotted mountings;
- front camber and castor are often fixed by the design, or have only a small adjustment.
If a fixed angle is outside the manufacturer's figures, a part is bent or a mounting has moved. The fix is to replace the part, never to bend it back. The technician prints a before-and-after report showing every angle against the specification.
Toe in millimetres and degrees
Toe can be given as a distance or an angle. A distance is usually measured across the wheel rim, so the same angle gives a bigger distance on a bigger wheel. To convert:
angle = inverse tan (toe distance ÷ rim diameter)
For example, 2 mm of toe measured across a 400 mm rim is an angle of inverse tan (0.005) ≈ 0.29°.
Safety and the MOT
Wheel alignment involves the steering and suspension, which are safety-critical, and work on an alignment ramp involves raised vehicles. It is for trained technicians only. The MOT inspection manual (section 2) treats track rod ends that are seriously misaligned as a major defect, and section 5.3 covers worn suspension joints – both things a technician looks for before alignment.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- DVSA MOT inspection manual: cars and passenger vehicles – 5. Axles, wheels, tyres and suspension
- DVSA MOT inspection manual: cars and passenger vehicles – 2. Steering
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.