▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Joints, bushes and anti-roll bars – Motor Vehicle Theory motor mechanics lesson

Lesson 81 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn how ball joints and rubber bushes let suspension parts move while keeping them in place, and how an anti-roll bar reduces body lean in corners – with the sums to prove it.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

The calculations use force = mass × acceleration and moments. Suspension joints are safety-critical parts: this lesson explains how they work and how wear is judged, not how to replace them. Values are dated; check the official source before relying on them. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Some off-road vehicles can disconnect their anti-roll bars. Why might that help when crawling over rocks, and why must they be reconnected for the road?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the anti-roll bar is a spring that holds the car up. The bar does almost nothing when both wheels rise together. It works only when the two sides move differently, as in a corner.
  • Thinking a rubber bush should be greased like a ball joint. A bonded bush works by twisting the rubber. It needs no grease, and oil can damage the rubber.
  • Thinking a stiffer anti-roll bar always improves grip. A stiffer bar reduces roll but moves load transfer to that end of the car, changing the balance between understeer and oversteer.

Hands-on: Make an anti-roll bar model: bend a wire coat hanger into a wide U shape and hold the middle in two loose loops of string tied to a box (the body). Press both ends down together and notice the bar just swings. Then push one end down while lifting the other and feel it resist as it twists. No real vehicle is needed; if you look at one, do so only with a qualified adult, with the car parked and switched off, and do not reach under it.

What you will learn

  • I can explain the difference between a ball joint and a rubber bush and where each is used.
  • I can explain why bushes are made of rubber and what happens when they wear.
  • I can describe how an anti-roll bar works and why it does little when both wheels rise together.
  • I can calculate a roll moment and a roll angle from given values.
  • I can apply the MOT wear limits for suspension pins and joints.

Key words

ball joint
A ball on a stud held in a socket, letting a suspension arm and a hub move at an angle while staying joined. It allows turning for steering as well as up-and-down movement.
bush
A sleeve of rubber (or a similar material) bonded between an inner and an outer metal tube. It lets an arm pivot by twisting the rubber, and it soaks up vibration.
anti-roll bar
A springy steel bar linking the suspension on the left and right, which twists when the car leans and so resists body roll. Also called a sway bar or stabiliser bar.
drop link
A short link joining each end of the anti-roll bar to the suspension arm or strut.
body roll
The body of the car leaning outwards in a corner.

The big ideas

Every suspension arm has to be fixed to the body and to the hub, yet free to move. Two kinds of joint do this. A ball joint is a ball in a socket, used where the parts must swivel in several directions, such as between a lower arm and a steered hub. A bush is a sleeve of rubber between two metal tubes, used where an arm only needs to pivot a little. The rubber twists instead of sliding, so it needs no grease and soaks up noise and vibration.

An anti-roll bar is a different kind of part. It is a U-shaped steel bar linking the left and right suspension. When the car leans in a corner, one side rises and the other falls, twisting the bar. The bar resists that twist, reducing body roll.

Worn joints and bushes cause knocks, wandering steering and uneven tyre wear, and they are checked closely in inspections. This lesson explains how they work and how wear is judged; replacing them is work for a trained technician.

Read-through: the teaching steps

  1. Ball joints

    A ball joint has a hardened ball on a tapered stud, held in a socket packed with grease and sealed by a rubber dust cover. The stud is fixed to one part, the socket to the other.

    On steered wheels, ball joints let the hub swivel for steering and move up and down with the suspension at the same time. If the dust cover splits, dirt gets in, the joint wears, and play develops. A badly worn ball joint can, in the worst case, separate.

  2. Rubber bushes

    A bush is rubber bonded to an inner and an outer metal sleeve. The inner sleeve is bolted to one part and the outer is pressed into the other. When the arm moves, the rubber twists.

    Rubber is used because it needs no lubrication, it soaks up vibration and road noise, and it lets the designer allow tiny controlled movements. Its weakness is that it can perish, crack or separate from the metal with age, oil and heat. Stiffer polyurethane bushes and fluid-filled bushes are used where more control or better isolation is needed.

  3. How an anti-roll bar works

    The anti-roll bar runs across the car. Its middle is held to the body in two rubber mountings, and each end is joined to a suspension arm by a drop link.

    • Both wheels rise together (a bump across the whole road): both ends of the bar move together, the bar barely twists and does little.
    • The car leans in a corner: the outer wheel rises relative to the body and the inner wheel falls. The ends move in opposite directions, the bar twists, and it pushes back, reducing roll.
  4. Roll and handling balance

    In a corner, the sideways force acts at the centre of gravity, above the axis the body rolls about. That makes a roll moment:

    roll moment = mass × sideways acceleration × height above roll axis

    The body leans until the springs and anti-roll bars push back with an equal moment. Roll angle = roll moment ÷ roll stiffness.

    Making the front bar stiffer moves more of the load transfer to the front tyres, which tends to make the car understeer; a stiffer rear bar tends towards oversteer. Designers use the bars to set this balance.

  5. Signs of wear

    Worn joints and bushes can cause:

    • knocks or clonks over bumps or when braking;
    • vague or wandering steering;
    • the car pulling under braking;
    • uneven tyre wear, because the wheel angles shift under load.

    A worn anti-roll bar link or mounting usually gives a light knock over uneven roads.

  6. Wear limits in the MOT

    Section 5.3.4 of the MOT inspection manual covers suspension joints, pins and bushes. Excessive wear is a major defect, and dangerous if the part is likely to detach. As a guide, play of more than 2 mm on a 12 mm pin, more than 3 mm on a 25 mm pin, or more than 10% of the diameter for pins over 25 mm, is excessive. A severely deteriorated dust cover is minor; a missing one, or one that no longer keeps out dirt, is major. Rubber bushes are rejected only for serious deterioration of the bonding or the rubber. Anti-roll bars are covered in 5.3.3: insecurely attached is major, fractured is dangerous.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.