Steering and suspension faults: symptoms and causes – Motor Vehicle Theory motor mechanics lesson
Lesson 83 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn to link what a driver feels and hears – a pull, a wander, a shimmy, a clonk – to the steering and suspension faults that cause it, and how a technician narrows the list down.
- Time
- 50 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson builds diagnostic reasoning from symptoms to causes. It is not a repair guide: steering and suspension are safety-critical, and a car with a serious fault should be checked by a trained technician. Values are dated; check the official source before relying on them. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “A driver says, "The car feels a bit odd but it still goes." What questions would you ask them to narrow down what is wrong, before anyone even looks at the car?”
- Later: the homework, then the practice test.
Watch out for
- Measuring the wheel alignment before checking for worn joints. Worn joints let the angles change while driving. Check tyres, then wear, then measure.
- Thinking every pull is a wheel alignment fault. Low tyre pressure, a faulty tyre, sticking brakes or worn bushes can all cause a pull. Check the simple causes first.
- Thinking a car with a dangerous steering fault can be driven gently to a garage. A dangerous defect means a direct and immediate risk. The vehicle should not be driven until it is repaired; recovery is the safe choice.
Hands-on: Make a fault-finding card for each symptom in the lesson (pull, wander, shimmy, clonk, heavy steering, bounce, sag). On the back write the likely causes, starting with the simplest. Shuffle the cards and test a friend: read a symptom and ask for the first two checks. If you look at a real car's tyres for wear clues, do it only with a qualified adult, with the car parked, switched off and cold – look, do not touch any parts.
What you will learn
- I can link common symptoms (pull, wander, vibration, heavy steering, clonks, bounce) to likely causes.
- I can tell a pull caused by the steering or tyres from one caused by the brakes.
- I can read tyre wear patterns as clues to steering and suspension faults.
- I can describe a logical order for diagnosis, starting with the simplest checks.
- I can say how the MOT grades common steering and suspension defects.
Key words
- symptom
- What the driver notices: a feeling, a sound, a sight or a smell. A symptom points to possible causes but does not prove one.
- pull
- The car steadily drifting to one side when the steering wheel is held lightly on a straight, level road.
- wander
- The car needing constant small steering corrections to stay straight.
- shimmy
- A side-to-side shaking of the steering wheel, often at a particular speed.
- diagnosis
- Working out the cause of a fault by gathering information and testing likely causes in a logical order.
The big ideas
Steering and suspension faults usually announce themselves. The car pulls to one side, wanders, shakes at a certain speed, clonks over bumps, bounces too much or wears its tyres strangely. Each symptom has a short list of likely causes, and a good technician uses the symptoms, and the order in which they appear, to narrow the list down.
The golden rule of diagnosis is to start simple. Tyre pressures and tyre condition cause many steering complaints, and they are quick to check. After that comes a visual check for damage and leaks, then a check for wear in joints and bushes, and only then measurement of the wheel angles.
This lesson is about recognising symptoms and understanding causes. Steering and suspension are safety-critical: a car with a serious fault should not be driven, and all checks and repairs on a real vehicle are for trained technicians.
Read-through: the teaching steps
Start with the tyres
Before blaming the steering, a technician checks the tyres:
- a tyre with lower pressure on one side makes the car pull towards that side;
- tyres of different sizes or types on the same axle can cause a pull;
- a tyre with an internal fault can pull, or shake at speed.
These are quick to check and very common, so they come first.
Pull: steering, tyres or brakes?
A pull all the time on a straight, level road usually points to tyres or wheel alignment – especially camber or castor that differs from side to side.
A pull only when braking points to the brakes: one side gripping harder than the other, or a worn suspension bush letting a wheel move under braking.
Remember that roads are built with a camber so rain drains away, which makes most cars drift gently towards the edge. A fair test uses a flat road.
Wander, shimmy and vibration
- Wander – often worn steering joints, a worn rack, or wrong toe.
- Shimmy at the steering wheel at one speed – often an out-of-balance front wheel, a bent wheel or a tyre fault; worn joints make it worse.
- Vibration felt through the seat – often a rear wheel out of balance, or a drivetrain fault.
A vibration that rises and falls with road speed, not engine speed, points to the wheels, tyres or hubs.
Noises: clonks, knocks and creaks
- A clonk over bumps – worn drop links, anti-roll bar mountings, ball joints, bushes or damper top mounts.
- A knock when braking or setting off – worn suspension arm bushes.
- A creak or groan when steering at low speed – a dry strut top mount bearing or a worn ball joint.
- A rumble that grows with speed and changes when cornering – a worn wheel bearing.
Heavy steering and poor return
- Heavy steering – low tyre pressures, a power steering fault (low fluid, a slipping belt or an EPS fault), or a seized joint.
- Steering that does not return to the centre – a seized joint or strut top mount, or wrong castor.
- Steering wheel not straight when going straight – wrong toe, a thrust angle that is not zero, or a bent part.
Bounce, sag and tyre clues
- Floating or continued bouncing, nose dive under braking – worn dampers.
- One corner sitting low – a broken or weak spring, or an air suspension leak.
- Tyre wear clues: one shoulder worn – camber; feathered tread – toe; cupped patches round the tyre – worn dampers or an out-of-balance wheel; both shoulders worn – under-inflation; centre worn – over-inflation.
How the MOT grades these faults
The MOT inspection manual grades steering and suspension defects. Some examples:
- steering free play more than 13 mm on a rack and pinion (48 mm with several joints, 75 mm for other steering gear, based on a 380 mm wheel) – major;
- a steering ball joint with excessive wear – major; with a serious risk of detachment – dangerous;
- a wheel bearing with excessive play – major;
- a spring fractured – major; a main leaf fractured – dangerous;
- a damper with negligible damping or severe leakage – major;
- suspension joint play over 2 mm on a 12 mm pin, 3 mm on a 25 mm pin, or 10% of the diameter above 25 mm – excessive wear, major.
Dangerous defects mean the vehicle should not be driven until repaired.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 15 min | Not assessed, self-checked |
| Worked examples and guided practice | 10 min | Marked by Classfern |
| Independent practice (three levels) | 16 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- DVSA MOT inspection manual: cars and passenger vehicles – 5. Axles, wheels, tyres and suspension
- DVSA – Overview of MOT changes from May 2018
- DVSA MOT inspection manual: cars and passenger vehicles – 2. Steering
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.