Tyre construction: radial plies, belts and compounds – Motor Vehicle Theory motor mechanics lesson
Lesson 84 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Look inside a tyre at its plies, belts, beads and liner, compare radial and cross-ply construction, and see why the rubber compound is a balance between grip, wear and rolling resistance.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The calculation uses pressure = force ÷ area. Inflated tyres store a lot of energy, so fitting, repairing and inflating them is for trained fitters. Values are dated; check the official source before relying on them. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why might a tyre maker offer different compounds for a family car, a sports car and a car used in snowy mountains?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the ripples on a radial sidewall are bulges. Gentle, even ripples are normal on radial tyres. A bulge is a local lump caused by damage to the structure, and it is dangerous.
- Thinking a softer tread compound is always better. Soft rubber grips well but wears quickly and may raise rolling resistance. The compound is chosen to balance grip, wear and economy.
- Thinking the air alone holds up the car. The air pressure and the carcass work together: the plies hold the pressure and carry the load. Damaged cords mean the structure can fail.
Hands-on: Build a paper model of tyre construction: draw a ring for the tyre, then use coloured pencils to draw radial body cords running straight across, and two belts crossing at an angle under the tread. Draw a second ring with cross-ply cords crossing diagonally. Compare them. If an old cut-open tyre section is available at a school workshop, look at it with a teacher. Never cut into a tyre yourself or try to inflate one.
What you will learn
- I can name the main parts inside a tyre and say what each does.
- I can explain the difference between radial and cross-ply construction and why radials are used on cars.
- I can explain how the rubber compound trades grip against wear and rolling resistance.
- I can estimate the size of a contact patch from load and pressure.
- I can explain why the MOT fails exposed cords, structural bulges and mixed construction on one axle.
Key words
- ply
- A layer of rubber-coated fabric cords (such as polyester or nylon) that forms the body, or carcass, of the tyre.
- radial tyre
- A tyre whose body plies run straight across from bead to bead, at about 90° to the direction of travel, with stabilising belts under the tread.
- belt
- A layer of rubber-coated steel cords under the tread of a radial tyre that keeps the tread flat and stiff.
- bead
- A hoop of steel wire at the inner edge of each sidewall that holds the tyre tightly on the rim.
- compound
- The recipe of rubbers and fillers (such as carbon black and silica) used for the tread.
The big ideas
A tyre looks like a simple rubber ring, but it is a carefully built structure. Inside the rubber are layers of fabric and steel cords, each with a job: to hold the air pressure, carry the weight of the car, keep the tread flat on the road and hold the tyre on the rim. The rubber on the outside is a recipe chosen to grip the road while wearing slowly.
Almost every modern car tyre is a radial tyre. Its body cords run straight across from one bead to the other, and steel belts under the tread stiffen it. Older cross-ply tyres had cords running diagonally, criss-crossing each other. The radial design lets the sidewall flex while the tread stays flat, giving better grip, longer life and lower fuel use.
This lesson explains how a tyre is built so you can understand its markings, its wear and the reasons for the safety rules. Tyres store a great deal of energy when inflated; fitting, repairing and inflating them is work for a trained tyre fitter.
Read-through: the teaching steps
The parts of a tyre
Working from the inside out:
- Inner liner – a thin layer of special rubber that keeps the air in (modern car tyres have no inner tube).
- Carcass plies – rubber-coated fabric cords forming the body. They carry the load and hold the pressure.
- Beads – hoops of steel wire at each edge, wrapped by the plies, holding the tyre on the rim.
- Belts – steel-cord layers under the tread, often with a nylon cap ply on top to hold them together at speed.
- Tread – the thick rubber that touches the road, with grooves to clear water.
- Sidewall – flexible rubber protecting the plies and carrying the markings.
See the drawing of the sidewall on the lesson page.
Reading a tyre size code. Radial construction
In a radial tyre, the carcass cords run straight across from bead to bead, like the lines of longitude on a globe. On their own they would let the tread squirm, so steel belts are laid under the tread at an angle, crossing each other, to make it stiff.
The result is a tyre with two separate jobs: a flexible sidewall that soaks up bumps, and a stiff, flat tread that grips and wears evenly. Radial sidewalls show gentle ripples when inflated. These are normal and must not be confused with a bulge.
Cross-ply construction
In a cross-ply tyre, the plies run diagonally, each layer at an angle to the one below, so they criss-cross. The sidewall and tread are tied together, so when the sidewall flexes, the tread distorts too.
Cross-ply tyres are tough and still used on some trailers, classic cars and off-road machines, but they grip less and run hotter on cars. Because radial and cross-ply tyres behave so differently, they must not be mixed on the same axle.
Compounds: a balancing act
The tread rubber is a recipe of natural and synthetic rubbers, carbon black, silica, oils and other ingredients.
- A softer compound grips better but wears faster.
- A harder compound lasts longer but grips less, especially in the wet.
- Silica improves wet grip while reducing rolling resistance, which saves fuel.
- Winter compounds stay flexible in the cold, when summer rubber goes hard.
No compound is best at everything: each tyre is a compromise chosen for its job.
The contact patch
Only a small area of each tyre touches the road – about the size of a hand. As a rough model, the air pressure supports the load, so:
contact patch area ≈ load on the tyre ÷ inflation pressure
A lower pressure gives a bigger, flatter patch but makes the sidewalls flex more and heat up. A higher pressure gives a smaller patch. This is one reason the vehicle maker's pressure must be used.
Construction and the MOT
The MOT inspection manual (section 5.2.3) reflects the tyre's construction. Any ply or cord visible without touching the tyre is a fail. A cut deep enough to reach the ply or cords is a major defect if it is longer than 25 mm or 10% of the section width, whichever is greater. A lump, bulge or tear caused by separation or partial failure of the structure is dangerous, and testers are told to tell normal radial ripples from a real bulge. Radial and cross-ply tyres mixed on the same axle is a major defect.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Wheels and tyres lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.