Pistons, rings and connecting rods – Motor Vehicle Theory motor mechanics lesson
Lesson 22 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how pistons, piston rings and connecting rods carry the force of combustion to the crankshaft, and calculate the forces involved.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains pistons and rods using example figures. The activity uses card tubes and rubber bands. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why is aluminium a good choice for pistons, even though steel is stronger?”
- Later: the homework, then the practice test.
Watch out for
- Thinking piston rings are just for holding oil in. Compression rings seal gas; the oil control ring manages oil.
- Thinking pistons are perfectly round when cold. They are shaped to become round at running temperature.
- Using the diameter instead of the radius in A = πr². Use A = π × d² ÷ 4 with the diameter, or π × r² with the radius – not π × d².
Hands-on: Make a model piston from a cardboard tube section and rubber bands as rings. Slide it in a slightly larger tube and feel how the 'rings' seal. Then calculate the crown area of your model's circle using A = π × d² ÷ 4 with a ruler measurement.
What you will learn
- I can describe the parts of a piston and the jobs of the rings.
- I can describe the connecting rod and how it joins piston and crankshaft.
- I can explain why rings have an end gap and pistons are shaped for expansion.
- I can calculate piston area and the force from gas pressure.
- I can link worn rings to symptoms such as blow-by and oil burning.
Key words
- piston
- The sliding plug in the cylinder that is pushed down by combustion pressure.
- compression ring
- A ring that seals combustion gas above the piston.
- oil control ring
- A ring that scrapes excess oil from the cylinder wall.
- connecting rod
- The rod linking the piston to the crankshaft.
- blow-by
- Combustion gas that escapes past the piston rings into the crankcase.
The big ideas
In a spark-ignited engine, the US Department of Energy explains, fuel mixed with air is ignited by the spark plug in the combustion chamber. The burning gas pushes on the piston with tremendous force. The piston must slide freely in its cylinder, yet seal the gas; it must survive heat and pressure many times a second, yet be light. Its rings provide the seal, and the connecting rod carries the force to the crankshaft.
This lesson explains how these parts work, how they are designed for heat, and how to calculate the force on a piston. Figures in examples are for practice only; real specifications come from the manufacturer's data, and engine work is done by trained technicians.
Read-through: the teaching steps
The piston
A piston is usually aluminium alloy: light and a good conductor of heat. Its parts are the crown (top), ring grooves, skirt and the bosses that hold the piston pin. Pistons are made slightly oval or tapered so they become round when hot, because the thicker parts expand more. See the piston in the drawing on the lesson page.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. Piston rings
Most car pistons carry three rings:
- top compression ring – seals combustion pressure;
- second ring – helps seal and scrape oil;
- oil control ring – scrapes excess oil off the wall, leaving a thin film.
Each ring has an end gap so it can expand when hot without its ends meeting.
The connecting rod
The connecting rod links the piston to the crankshaft. The small end fits on the gudgeon pin in the piston; the big end clamps round the crankpin with a split bearing. Rods are usually forged steel with an I-section for strength with low mass.
The force on a piston
Force = pressure × area.
Piston crown area A = π × d² ÷ 4.
Peak cylinder pressures are many times atmospheric pressure, so even a small piston receives a force of several tonnes at the peak of combustion – for a moment.
Blow-by and crankcase ventilation
No ring seals perfectly. A little gas – blow-by – passes into the crankcase. Positive crankcase ventilation draws it into the intake to be burned. Worn rings increase blow-by, reduce compression and let oil into the chamber, where it burns and can show as bluish exhaust smoke.
Clearances and measurement
Technicians check piston-to-bore clearance, ring end gaps and ring-to-groove clearance against the manufacturer's data using micrometers, bore gauges and feeler gauges. Too little clearance risks seizure when hot; too much causes noise, blow-by and oil burning.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.